Braun HB701AI-MQ7087X - Инструкция по эксплуатации - Страница 16

16

Chopping (D)

Using the blade (9h) you can chop meat, hard 
cheese, onions, herbs, garlic, vegetables, bread, 
crackers, and nuts.

Refer to the Processing Guide D for maximum 
quantities, recommended times and speeds.

Before Use

• 

Pre-cut foods into small pieces for easier 
chopping.

• 

Remove any bones, cartilage, tendons and 
gristle from meat to help prevent damage to the 
blades.

• 

Remove stems from herbs, shell nuts.

• 

Make sure the anti-slip rubber ring (9g) is 
attached to the bottom of the food processor 
bowl.

Assembly and Operation

• 

Carefully remove the plastic cover from the 
blade.

• 

The blade (9h) is very sharp! Always hold it by the 
upper plastic part and handle it carefully.

• 

Place the blade on the center pin of the bowl (9f). 
Press it down and give it a turn so that it locks into 
place.

• 

Fill the bowl with food. Attach the lid (9a) to the 
bowl with the latch (9e) positioned to the right of 
the bowl handle and align with marks.

• 

To lock the lid, turn it clockwise so that the latch 
engages with a click.

• 

Insert the motor part (2) into the coupling (9b) 
until it locks.

• 

Plug in the appliance and insert the pusher (9c) in 
the feed tube (9d).

• 

To operate the food processor, switch on the 
appliance. During processing, hold the motor 
part with one hand and the food processor bowl 
on the handle.

• 

When chopping is complete, unplug and press 
the EasyClick Plus release buttons (3) to detach 
the motor part.

• 

Press the lid latch (9e) and hold it. Turn the lid 
(9a) counter-clockwise to unlatch it.

• 

Lift the lid up. Carefully take out the blade before 
pouring out the contents of the bowl. To remove 
and unlock the blade, slightly turn it then pull it 
off.

Caution

• 

Do not use the food processor accessory to chop 
extremely hard foods, such as unshelled nuts, ice 
cubes, coffee beans, grains or hard spices e.g. 
nutmeg. Processing these foods could damage 
the blades.

• 

Never place the food processor bowl in the 
microwave oven.

Using the blade (9h), you may also mix light batter 
like a pancake batter or a cake mixture based on up 
to 250 g of flour.

Recipe Example: Pancake Batter
375 ml milk
250 g plain flour
2 eggs

• 

Pour milk into the bowl, then add flour and finally 
the eggs.

• 

Using full speed, mix the batter until smooth.

Kneading Dough (D)

Figure F also applies for the use of the kneading 
hook (9i). The kneading hook is ideal for kneading 
different dough types such as yeast or pastry.

Assembly and Operation

• 

Place the kneading hook on the center pin of the 
bowl (9f). Press it down and give it a turn so that it 
locks into place.

• 

Fill the bowl with flour (max. 250 g), then add the 
other ingredients except the liquids.

• 

Turn the appliance on with ¾ way pressure on the 
Smartspeed switch.

• 

Add liquids through the feed tube while the motor 
is running. 
NOTE: Maximum kneading time: 1 minute – then 
allow the motor to cool down for 10 minutes.

Recipe Example: Pizza dough
250 g plain flour
½ tsp salt
½ tsp dried yeast
5 tbsp olive oil
150 ml water (lukewarm)

• 

Put all ingredients except water into the bowl and 
start kneading.

• 

Add water through the feed tube while the motor 
is running.

Recipe Example: Sweet Pastry
250 g plain flour
170 g unsalted butter (cold/hard, small pieces)
80 g sugar
1 vanilla sugar
1 small egg
1 pinch salt

• 

Put butter and sugar into the bowl and start 
kneading. For good results use cold butter.

• 

Add flour and the rest of the ingredients.

• 

Dough will become too soft from over kneading. 
Stop kneading shortly after dough has formed a 
ball.

• 

Cool down the dough in the refrigerator for half 
an hour before proceeding.

Slicing / Shredding / French Fry (E)

Use the fine and coarse shredding inserts (i) to 
shred foods such as apples, carrots, potatoes, 
beetroot, cabbage, hard cheese (like Parmesan).
Use the French fry disc (9k) to prepare french fries.

Refer to the Processing Guide E for recommended 
speeds.

5722113494_01_MQ 7075x_7087x_INT_S6-144.indd   16

5722113494_01_MQ 7075x_7087x_INT_S6-144.indd   16

04.07.19   14:15

04.07.19   14:15