APC Panel - Инструкция по эксплуатации

3-16kVA Service Bypass Panels

©2009 APC by Schneider Electric, APC, the APC logo, and Smart-UPS are

owned by Schneider Electric industries S.A.S American Power Conversion

Corporation, or their affiliated companies. All other trademarks are property

of their respective owners.

990-1530B

Note: Read the safety information sheet before installation.

Illustrations in this document may differ slightly from the actual hardware.

Attention: This product is for use in a controlled environment. Refer to product
specifications for environmental limits.

R

ACK

M

OUNTING

n

o

Set SBP in the rack. If hardwiring is required, see

Connecting Power

section before screwing into the rack.

W

ALL

M

OUNTING

n

o

Whenever possible, attach one top screw and one bottom screw into a wall stud. If stud

mounting is not possible, use an expandable wall anchor.

Screws are not included

; .25” x

2” lag bolts are recommended.

T

OWER

O

PTION

(

FOR

S

MART

-UPS

RT

SETUPS ONLY

)

n

Remove screw from the top and bottom rear of both the UPS and SBP. Install tie

brackets and reattach screws.

o

Unscrew and remove top cover of the

UPS.

p

Attach bracket to top of UPS and SBP.

q

Reattach top cover of the UPS.

Note: The SBP5000RMI2U, when used in conjunction with an SURT3000XLI or SURT5000XLI UPS in a
tower configuration without an external battery pack (SURT192XLBP), is suitable for mounting on
concrete or other non-combustible smooth surfaces only.

U

SER

C

ONFIGURABLE

Attention: When using an online UPS, put the UPS in automatic bypass mode before
rotating the SBP switch.

1. Normal:

Power is directed from the utility outlet, through the Bypass Panel and UPS,

and to connected equipment. For use during normal UPS operation.

2. Test:

Power supplied to the UPS is not output. Use when tests are being conducted on

the UPS, and connected equipment is not yet desired.

3. Bypass:

Power from the utility outlet is filtered through the Bypass Panel, and to the

connected equipment. Use to bypass the UPS, when functioning improperly.

Note: While operating in ‘Test’ or ‘Bypass’ mode, power to the connected equipment is
not conditioned by the UPS. At this time, the “Equipment Protection Policy” is not valid.

I

DENTIFYING THE

P

ANEL

Service Bypass Panels will differ. Refer to chart for unit specifications.

Note: HW= Hardwire

Service Bypass

Panel

Corresponding

UPS Systems

Bypass

Input

UPS

Input

UPS

Output

PDU

Panel

SBP3000RM2U

100-120V Smart-UPS

3kVA

L5-30P

L5-30R

L5-30P

(2) 5-20R,

(6) 5-15R

SBP5000RMT2U

200/208/240V

Smart-UPS 3-4.5kVA

L6-30P

L6-30R

L6-30P

(2) L6-20R,

(2) L6-30R

SBP5000RMI2U

*

230V Smart-UPS

3-5kVA

C20/HW

C19/HW

C20/HW

(2) C19,

(8) C13

SBP6KRMT2U

**

200/208/240V

Symmetra 2-6kVA

L6-30P/

HW

L6-30R/

HW

L6-30P/

HW

(1) L6-20R,

(2) L6-30R

SBP6KRMI2U

230V Symmetra

2-6kVA

HW

HW

HW

(4) C19

SBP3000

100-240V Smart-UPS

3-5kVA with 30A HW

input/output

available

HW

HW

HW

HW

SBP10KRMT4U

200/208/240V

Smart-UPS RT

7.5-10kVA

HW

HW

HW

(3) L6-20R,

(3) L6-30R

SBP10KRMI4U

230V Smart-UPS RT

7.5-10kVA

HW (3Ph

or 1Ph)

HW (3Ph

or 1Ph)

HW

(8) C13,

(2) C19

SBP16KP

200-240V

Symmetra LX

4-16kVA

HW (3Ph

or 1Ph)

HW (3Ph

or 1Ph)

HW

HW

SBP16KRMI4U

220-240V

Symmetra LX

4-16kVA

HW (3Ph

or 1Ph)

HW (3Ph

or 1Ph)

HW

(3) 30A HW

SBP16KRMP4U

200/208/240

Symmetra LX

4-16kVA

HW

HW

HW

(6) L14-30R

SBP16KRMP4U-HW

200/208/240

Symmetra LX

4-16kVA

HW

HW

HW

(1) L14-30R,

(3) L5-20R,

(1) 100A HW

*

For loads exceeding 3kVA, hardwiring is necessary.

**

For loads exceeding 5kVA, hardwiring is necessary.

x4

x4

x4

x8

Rear

Front

x1

x4

x8

x2

x2

x2