Акустика Sven MS-3000 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
ENG
25
Operation Manual
MS-3000
MSS
с
onnecting and control
MS-3000 Multimedia Speaker System can be connected to virtually any audio source:
CD/DVD/ MP3, TV, PC sound card, etc. (see connection diagram in Fig. 4).
•
Before making any connections, make sure the MSS is o
ff
and unplugged. Then connect
satellites and the subwoofer to the ampli
fi
er module. To do this use audio cables (included) to
connect the left speaker to the «L+» and «L–» jacks, and the right speaker to the «R+» and «R-»
jacks of SATELLITES L/R
p
of the ampli
fi
er module following to the polarity. Then with the third
audio cable (included) connect a subwoofer to
SUBWOOFER
q
«+» and «-» jacks of the
ampli
fi
er module following to the polarity as well (see diagram in Fig. 4).
Note. Check the reliable
fi
xation of wires in terminals, connection compliance with
polarity and the absence of contact of bared wires with each other and the metal parts
of the hardware.
•
To connect the MSS to a PC or
МР
3/CD player, use the 2RCA – mini-jack signal cable
(included). For this at
fi
rst plug the RCA jacks of the signal cable in the L
и
R jacks of PC AUDIO
INPUT
n
, and then plug the signal cable mini-jack (Ø 3.5 mm) in LINE OUT port of the PC
sound card or in
МР
3/ CD-player OUTPUT, as shown in Fig. 4.
Note. The MSS can be also connected to PC,
МР
3/CD-player with the signal cable of
mini-jack to mini-jack (not included). For this, at
fi
rst, connect the signal cable
mini-jack to AUX2 line input
m
on the ampli
fi
er module front panel and the second
signal cable mini-jack to LINE OUT port of the PC sound card or to the
МР
3/CD-player
AUDIO OUTPUT.
•
Use the 2RCA to 2RCA signal cable (not included) to connect the MSS to a TV, DVD/CD
players. To do this, use the signal cable to connect L and R jacks of the ampli
fi
er module AUX1
audio input
n
with TV or DVD/CD-player audio outputs, as shown in Fig. 4.
Note. The sound is directly dependent on accuracy and reliability of the cable
connections. It’s recommended to use the cables supplied with the speakers.
•
Plug the power cable (included) in power cable jack
u
. Then connect the MSS to the mains
outlet.
•
Turn on the device using POWER switch (
t
, ON position) on the ampli
fi
er module.
•
Turn on the MSS using button
b
on the ampli
fi
er module or button
a
on the RC.
•
Select a desired audio source by pressing short INPUT button
i
on the ampli
fi
er module
front panel or INPUT button
b
on the remote control.
•
Adjust the volume level by turning VOLUME knob
i
on the ampli
fi
er module front panel or
VOL+/- buttons
g
on the remote control (Fig. 3).
•
Adjust high and low frequency levels by turning TREBLE
g
and BASS
h
knobs accordingly
on the ampli
fi
er module front panel or with VOL+/- buttons
g
on the remote control, by
pressing MODE button
e
previously (Fig. 3).
•
If necessary adjust the balance level between the left and right channels by L/R
c
/
h
buttons on the remote control, previously selecting the mode by pressing MODE button
e
(Fig. 3).
•
To listen to the radio direct the antenna for better reception, connecting it to the ANT jack
r
previously, as shown in Fig. 4.
•
Press RESET button
f
on the remote control to reset timbres.
•
After using the MSS, mind to switch it o
ff
using ON/OFF switch (
t
, OFF position) and unplug
the power cable from the socket as well.
