Акустика Sven MS-2000 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
ENG
25
Operation Manual
MS-2000
w
VOL+/-: volume control
x
CLOCK: show current time
Battery Installation
•
Open the battery compartment on the back of the remote control.
•
Insert the included AAA batteries.
•
Close the battery compartment.
Notes:
• Use the RC at an angle no more than 30° at a distance of no more than 7 meters.
• Direct the remote control at the LED display on the subwoofer.
• If the remote control does not work, check the batteries or replace the discharged
batteries with new ones.
• Remove the batteries from the RC if you don’t intend to use it for a long time.
* The frequencies are switched if there are stations preset in the memory.
** The storage device must be formatted as FAT, FAT32. Connecting devices other than USB
fl
ash drive is
not recommended. Connection of HDDs and other devices can cause damage to the MSS.
5. PREPARATION AND OPERATION
Speaker placement
•
Place the speakers symmetrically to the listener at least one meter away. The subwoofer emits
non-directional sound, therefore it can be located in any place of the room where it sounds the best.
•
Place MSS far away from monitors and TV sets, as insigni
fi
cant image distortion in these super-
sensitive devices is possible.
Installation and operation
MS-2000 speaker system can be connected to virtually any audio devices: DVD/CD players, PCs,
laptops, etc. (see connection diagram in Fig. 5).
•
Before making any connections, make sure the MSS is o
ff
and unplugged. Then connect speakers
to the subwoofer AUDIO OUTPUT L/R
n
terminals with the help of included audio cables. Observing the
polarity connect the right speaker to the subwoofer AUDIO OUTPUT R with the audio cable and the left
speaker – to the AUDIO OUTPUT L. Pay attention that the plus (red) cable wires of speakers must be
connected to the subwoofer plus terminals (+
→
+) and the minus (black) cable wires of speakers – to the
subwoofer minus terminals (–
→
–) (see connection diagram in Fig. 5).
Note. Check the reliable
fi
xation of wires in the terminals, polarity of connection and
absence of contact of the bared wires with each other and the metal parts of the hardware.
•
To connect the MSS to a PC,
МР
3/CD player, use a 2RCA to mini-jack signal cable (included).
Insert the RCA jacks of the signal cable into the L and R jacks of the PC AUDIO INPUT
l
, and the
mini-jack of the signal cable – into the LINE OUT port of your PC sound card or an audio output of
your
МР
3/ CD player, as shown in Fig. 5.
•
To connect the MSS to a TV or DVD/CD player, use a 2RCA to 2RCA signal cable (not included).
Insert the RCA jacks of the signal cable into the L and R jacks of the PC AUDIO INPUT
l
, and the
other RCA jacks – into your TV or DVD/CD player audio output jacks, as shown in Fig. 5.
•
Connect the subwoofer to the mains outlet with the power cord
j
.
•
Turn on the MSS power supply using the ON/OFF s w i t c h (
i
, ON) on the subwoofer rear panel.
26
y
RESET: return to default settings
DISP+/-: adjust display brightness
