Вытяжки Whirlpool WHBS 62F LT K - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
12
It can also be performed manually (see paragraph “
Sensor set up
”).
During calibration, which lasts for 5 minutes,
T4
will flash and lights can be used.
T1. FAN MOTOR OFF / DECREASE SPEED
Press to decrease speed and switch the extraction motor OFF. Press and hold to directly switch the extraction motor OFF.
T2. FAN MOTOR ON / INCREASE SPEED
Press to switch the extraction motor ON and increase speed. Press and hold to set 3th speed directly.
T3. “POWER BOOST “ FUNCTION
Press
T3
to activate the “
POWER BOOST 1
” intensive extraction speed (time-controlled).
Please note: the hood will go back to running at the 3th speed, after five minutes.
With the extraction motor on, in “POWER BOOST1”, press again
T3
to activated the “
POWER BOOST 2
” additional intensive extraction
speed (time-controlled).
Please note: the hood will go back to running at the 3th speed, after five minutes.
Please note: press again
T3
, during the five minutes, the hood will go back to running in “
POWER BOOST 1
”
T4. 6TH SENSE FUNCTION (AUTO MODE) ON/OFF
The hood set the extraction speed automatically if the sensor in the hood detects changing on ambient conditions.
Please note: to make sure this function is used correctly first
configure sensor
(see “
Sensor set up
” below).
Please note: if you change any other functions that control the speed, the “
6th sense
” function will switch off.
Sensor set up
This can be done when the hood is OFF.In normal ambient conditions press
T4
for 5secs,
T4
flashes for 5 mins to indicate hood is performing
sensor calibration, then switches off to indicate the calibration has ended.
Setting cooktop:
Press and hold
T1
and
T2
simultaneously. Both lit to indicate hood is ready to accept cooktop parameter calibration.
Press
T1
to choose Gas hob (
T1
starts to flash for 3 secs to indicate hood parameters are set for gas hob).
Press
T2
to choose Induction hob (
T2
starts to flash for 3 secs to indicate hood parameters are set for induction hob).
T5. OPERATION “ZEN MODE”
Press to activate or deactivate the “ZEN”
extraction
mode.
This function makes it possible to activate an extraction speed with the perfect balance between quietness and extraction efficiency.
T6. GREASE/CHARCOAL FILTER ALARM/RESET
At regular intervals, the hood signals the need to perform filter maintenance.
Please note: The indicators will only work when the hood is on.
T6
lit: Carry out maintenance on the grease filter.
T6
flashing: carry out maintenance of the charcoal filter.
Resetting the filter saturation indicators:
Please note: This must be done with the hood switched on.
Press and hold
T6
Please note: T6 and hood switch off, to indicate alarm reset is done.
The reset of the Grease Filter and Charcoal Filter is performed using the same key. If both filters alarms are active, the reset procedure will
reset the counter one by one, with priority to the Charcoal.
Activating the carbon filter saturation indicator
Please note: This must be done with the extraction motor switched off.
This indicator is usually deactivated – press and hold
T3
and
T7
simultaneously to activate the function: Both will lightup to indicate activation.
To deactivate the function, press and hold the same buttons again: Both will flash briefly and then switch off to indicate deactivation.
T7. MAIN LIGHT ON/OFF
Press to switch the hob lights on or off.
