Falmec TIME 115 - Инструкция по эксплуатации - Страница 21

21

ENGLISH

1) - CREATE A NEW CODE

The procedure is to be carried out on the radio control.

•

  Press LIGHT 

 and TIMER 

 simultaneously until the display starts 

flashing.

•

  Press DOWN 

 on the radio control: saving is confirmed by three 

brief flashes of the display. The new code cancels and replaces the 
previous default code. 

Reconnect the hood to the electrical power supply, making 

sure that the lights and motor are off. 

2) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD

           USING THE ELECTRONIC PUSHBUTTON PANEL

press TIMER (

) 

on the hood pushbutton panel

 for 2 seconds:

the red LED lights up. 
press any key on the radio control within 10 seconds. 

RESTORING DEFAULT CODE

the procedure is to be carried out if the hood is disposed of, sold or 
transferred.

Disconnect the power to the hood before starting the pro-

cedure.

•

  Press UP 

 and DOWN 

 simultaneously on the radio control for 

more than 5 seconds: reset is confirmed by three brief flashes of the 
display. 

•

  Reconnect the hood to the electrical power supply.

•

  Proceed with associating the hood and the radio control, as de-

scribed in point 2.

 MAINTENANCE

Before cleaning or carrying out maintenance operations, 

disconnect the equipment by removing the plug or 

switching off the main switch.

Do not use detergents containing abrasive, acidic or corrosive 

substances or abrasive cloths.

Regular maintenance guarantees proper operation and performance 
over time.
Special attention is to be paid to the metal anti-grease filters and active 
carbon filters: frequent cleaning of the filters and their supports ensures 
that no flammable grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood 

 at least 

once every 15 days 

to prevent oily substances and grease from stick-

ing to them. To clean the brushed stainless steel hood, the Manufac-
turer recommends using ''Magic Steel'' wipes. Alternatively, it can be 
cleaned using a damp cloth, slightly moistened with neutral, liquid 
detergent or denatured alcohol. Finish off cleaning by rinsing well and 
drying with soft cloths. 

Do not use too much water next to the push button con-

trol panel and lighting devices in order to prevent humid-

ity from reaching electronic parts.

The glass panels can only be cleaned with specific, non-corrosive or 
non-abrasive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with 
these instructions.

CLEANING OF INTERNAL SURFACES

It is forbidden to clean electrical parts, or parts related to 

the motor inside the hood, with liquids or solvents.

For the internal metal parts, see the previous paragraph.

METAL ANTI-GREASE FILTERS

It is advised to 

frequently

 was the metal filters (

at least once a month

) 

leaving them to soak in boiling water and washing up liquid for 1 hour, 
taking care not to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reas-
sembling them. Washing in a dishwasher is permitted, however, it may 
cause the filter material to darken: to reduce the possibility of this prob-
lem from happening, use low-temperature washes (55°C max.).
To extract and insert the metal anti-grease filters see the assembly in-
structions.

ACTIVE CARBON FILTERS

These filters retain the odours in the air that passes through them. The 
purified air is recirculated into the environment.
The active carbon filters must be replaced on average every 3-4 months 
under normal conditions of use.

LIGHTING

The range hood is equipped with high efficiency, low consumption LED 
spotlights with extremely long duration under normal use conditions.
Should the LED spotlight need to be replaced, proceed as shown in 
the figure.

12V

3

1

2