Falmec EUROPA ISOLA 90 - Инструкция по эксплуатации - Страница 19

19

ENGLISH

SAFETY INSTRUCTIONS

AND WARNINGS

Installation operations are to be carried 

out by skilled and qualified installers in ac-

cordance with the instructions in this booklet and 

in compliance with the regulations in force.

DO NOT use the hood if the power supply cable 

or other components are damaged: 

disconnect 

the hood from the electrical power supply and con-
tact the Dealer or an authorised Servicing Dealer for 
repairs.

Do not modify the electrical, mechanical or func-

tional structure of the equipment.

Do not personally try to carry out repairs or re-

placements. Interventions carried out by incom-

petent and unauthorised persons can cause seri-

ous damage to the unit or physical and personal 

harm, not covered by the Manufacturer's warran-

ty.

WARNINGS FOR THE INSTALLER

TECHNICAL SAFETY

Before installing the hood, check the integ-

rity and function of each part. Should 

anomalies be noted, do not proceed with installa-

tion and contact the Dealer.

Do NOT install the hood if an aesthetic (or cos-

metic) defect has been detected. Put it back into 

its original package and contact the dealer.

No claim can be made for aesthetic (or cosmetic) 

defects once it has been installed.

During installation, always use personal protective 
equipment (e.g.: Safety shoes) and adopt prudent 
and proper conduct.
The installation kit (screws and plugs) supplied with 
the hood is only to be used on masonry walls: in case 
of installation on walls of a different material, assess 
other installation options keeping in mind the type 
of wall surface and the weight of the hood (indicated 
on page 2).
Keep in mind that installations with different types of 
fastening systems from those supplied, or which are 
not compliant, can cause electrical and mechanical 
seal danger.
Do not install the hood outdoors and do not expose 
it to atmospheric elements (rain, wind, etc.).

ELECTRICAL SAFETY

The electrical system to which the hood is 

to be connected must be in accordance 

with local standards and supplied with earthed 

connection in compliance with safety regulations 

in the country of use. It must also comply with Eu-

ropean standards regarding radio antistatic prop-

erties. 

Before installing the hood, check that the electrical 
mains power supply corresponds with what is report-
ed on the identification plate located inside the hood.
The socket used to connect the installed equipment 
to the electrical power supply must be within reach: 
otherwise, install a mains switch to disconnect the 
hood when required.
Any changes to the electrical system must be carried 
out by a qualified electrician. 
The maximum length of the flue fastening screws 
(supplied by the manufacturer) must be 13 mm. Use 
of non-compliant screws with these instructions can 
lead to danger of an electrical nature.
Do not try to solve the problem yourself in the event 
of equipment malfunction, but contact the Dealer or 
an authorised Servicing Department for repairs.

When installing the hood, disconnect the 

equipment by removing the plug or switch-

ing off the main switch.

FUMES DISCHARGE SAFETY

Do no connect the equipment to discharge 

pipes of fumes produced from combustion 

(for example boilers, fireplaces, etc.).

Before installing the hood, ensure that all standards in 
force regarding discharge of air out of the room have 
been complied with.

Deviation for Australia and New Zeland: Range hoods 
and other cooking fume extractors may adversely 
affect the safe operation of appliances burning gas 
or other fuels (including those in other rooms) due 
to back flow of combustion gases. These gases can 
potentially result in carbon monoxide poisoning. 
After installation of a range hood or other cooking 
fume extractor, the operation of flued gas appliances 
should be tested by a competent person to ensure 
that back flow of combustion gases does not occur. 
(AS/NZS 60335.2.31:2013/A4:2020)