Falmec BUILT-IN 50 MAX INOX - Инструкция по эксплуатации - Страница 16

16

TOUCH PUSHBUTTON PANEL 

(GRUPPO INCASSO MURANO)

ON/OFF (Blue led steady on)

Motor on/off and Speed 1 

ON/OFF (blue led flashing)

If pressed for more than 3 seconds, it activates the 24h cycle (1h ON -> 3h
OFF -> 1h ON)
the function deactivates if:
- The motor turns off (key 

)

- After 24h

Speed 2 activation

Speed 3 activation

Speed 4 is only active for a few minutes, then speed 3 
activates.

Light on/off
Short impulse: 

turn light on and off

Long impulse: 

change light tone from 2700K to 5600K

TIMER

(red LED flashing)

Auto switch-off after 15 min.
The function deactivates (red LED off ) if:
- The motor turns off (key 

 ).

- The speed is changed.

 USING THE RADIO CONTROL

WARNINGS!:

Place the hood away from sources of electromagnetic waves (e.g. micro-
wave ovens), which could interfere with the radio control and with the hood 

electronics.
The maximum operating distance is 5 metres, that may vary according to the pres-
ence of electromagnetic interferences. 
Radio control operated at 433.92MHz.
The radio control consists of two parts:
- the receiver built into the hood;
- the transmitter shown here in the figure.

DESCRIPTION OF TRANSMITTING COMMANDS

UP

Motor switch-on and speed increase from 1 
to 4. Speed 4 is only active for a few minutes.

DOWN

Speed decrease and motor switch-off.

Light ON-OFF
Short impulse:

turn light on and off

Long impulse:

change light tone from 2700K to 5600K

TIMER ON: 

The motor automatically switch-

es off after 15 min.
The function is automatically disabled if the 

motor is switched off (

 key)

Command transmission active

The radio control is optional for the GRUPPO INCASSO and Green Tech.
Follow the entire procedure described below if purchased.

Skip the activation procedure for IL GRUPPO INCASSO MURANO.

ACTIVATION PROCEDURE 

(for GRUPPO INCASSO and Green Tech)

Before using the radio control, follow the procedure below on the 

hood pushbutton panel

:

•

  Press LIGHT (

) and TIMER (

) simultaneously until all LEDs start flashing. 

•

  Release the two keys and press LIGHT (

) again until all LEDs are lit up. 

•

  Release LIGHT (

): now the receiver is active.

This procedure is also used to deactivate the receiver.

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.
With several radio controls in the same room, a new code can be created by following the 
procedure below.

Disconnect the power to the hood before starting the procedure.

1) - CREATE A NEW CODE

The procedure is to be carried out on the radio control.

•

 Press 

LIGHT 

 and TIMER 

 simultaneously until the display starts flashing.

•

 Press 

DOWN 

 on the radio control: saving is confirmed by three brief flashes of the 

display. The new code cancels and replaces the previous default code. 

Reconnect the hood to the electrical power supply, making sure that the 
lights and motor are off. 

2A) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD
           USING THE ELECTRONIC PUSHBUT TON PANEL
 

press TIMER (

)

on the hood pushbutton panel

 for 2 seconds:

the red LED lights up. 
press any key on the radio control within 10 seconds. 

2B) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD
           USING THE TOUCH PUSHBUT TON PANEL
 

press LIGHT (

)

on the hood pushbutton panel

 for 2 seconds:

the red LED lights up. 
press any key on the radio control within 10 seconds. 

RESTORING DEFAULT CODE

the procedure is to be carried out if the hood is disposed of, sold or transferred.

Disconnect the power to the hood before starting the procedure.

•

 Press 

UP 

 and DOWN 

 simultaneously on the radio control for more than 5 sec-

onds: reset is confirmed by three brief flashes of the display. 

•

  Reconnect the hood to the electrical power supply.

•

  Proceed with associating the hood and the radio control, as described in point 2.