Elica Joy BLIX/A/90 - Инструкция по эксплуатации - Страница 15

15 

or if the plug is not located in an accessible area, after 
installation,  apply a double pole switch in accordance with 
standards which assures the complete disconnection of the 
mains under conditions relating to over-current category III, in 
accordance with installation instructions. 
 

WARNING!

Before re-connecting the hood circuit to the mains supply and 
checking the efficient function, always check that the mains 
cable is correctly assembled. 
The hood is provided with a special power cable ; if the cable 
is damaged, request a new one from Technical Service. 

Mounting 

Before beginning installation: 

• 

Check that the product purchased is of a suitable size for 
the chosen installation area. 

•  Remove the charcoal (*) filter/s if supplied (see also 

relative paragraph). This/these is/are to be mounted only 
if you want lo use the hood in the filtering version. 

•  Check (for transport reasons) that there is no other 

supplied material inside the hood (e.g. packets with 
screws (*), guarantees (*), etc.), eventually removing 
them and keeping them. 

Expansion wall plugs are provided to secure the hood to most 
types of walls/ceilings. However, a qualified technician must 
verify suitability of the materials in accordance with the type of 
wall/ceiling. The wall/ceiling must be strong enough to take 
the weight of the hood.  

Do not tile, grout or silicone this appliance to the wall. 
Surface mounting only. 

Operation 

Control panel with 6 buttons 

 
To select the functions of the hood just touch the commands. 
 

Light key ON/OFF 

Intensive speed selection key

(suction 

power) - duration 5 minutes

: 

the hood sets this 

power and at the end of the 5 minutes returns 
to the previous setting. 

High-speed selection key 

(suction power). 

Medium-speed selection key

(suction power) 

- when flashing it indicates the need to wash or 
replace the carbon filter. This signal is normally 
deactivated. To activate the alarm, disable the 
electronic by pressing the 

0

button for 3 

seconds.  

Next, simultaneously press buttons 

1

 and 

2

 for 

3 seconds; at first, only button 

1

will flash, then 

both buttons 

1

 and 

2

will flash to indicate 

activation. Repeat the procedure to deactivate 
the alarm; at first buttons 

1

 and 

2

will flash and 

subsequently only button 

1

to indicate 

deactivation. 

Low-speed selection key

 (suction power) – 

when flashing it indicates the need to wash the 
fats filter. 

Motor key OFF

 (stand by) – excludes the 

electronics – reset wash/replace filters signals. 

MOTOR OFF 

Press briefly to switch the motor off. 

RESET FILTERS SIGNALS

In functioning mode, after carrying out filter 
maintenance, press the key until hearing the 
sound signal. The flashing LED 

1 

(grease filter) 

or 

2 

(carbon filter) stops flashing. 

EXCLUDING THE ELECTRONICS

Press the key for 3 seconds. The hood 
command electronics will be excluded. 
This function can be useful during the product 
cleaning operations. 
Just repeat the operation to reinsert the 
electronics.  

 
If the hood fails to operate correctly, briefly disconnect it from 
the mains power supply for almost 5 sec. by pulling out the 
plug. Then plug it in again and try once more before 
contacting the Technical Assistance Service. 

Maintenance 

Cleaning 

Clean using 

ONLY

 a cloth dampened with neutral liquid 

detergent. 

DO NOT CLEAN WITH TOOLS OR 

INSTRUMENTS

. Do not use abrasive products. 

DO NOT USE 

ALCOHOL! 

Grease filter 

Fig. 11-28 
Traps cooking grease particles. 

This must be cleaned once a month (or when the filter 
saturation indication system – if envisaged on the model in 
possession – indicates this necessity)  using non aggressive 
detergents, either by hand or in the dishwasher, which must 
be set to a low temperature and a short cycle. 
When washed in a dishwasher, the grease filter may discolor 
slightly, but this does not affect its filtering capacity. 
To remove the grease filter, pull the spring release handle. 

Charcoal filter (filter version only) 

Fig. 27 
It absorbs unpleasant odors caused by cooking. 

The activated charcoal filter can be one of these types: