Elica HIDDEN 2.0 IXGL/A/52 - Инструкция по эксплуатации - Страница 21

21 

WARNING!

Before re-connecting the hood circuit to the mains supply and 
checking the efficient function, always check that the mains 
cable is correctly assembled. 

Warning! 

If the supply cord is damaged, it must be replaced 

by the manufacturer, its service agent or similarly qualified 
persons in order to avoid hazard.  

Mounting 

Before beginning installation: 

• 

Check that the product purchased is of a suitable size for 
the chosen installation area. 

•  Remove the charcoal (*) filter/s if supplied (see also 

relative paragraph). This/these is/are to be mounted only 
if you want lo use the hood in the filtering version. 

•  Check (for transport reasons) that there is no other 

supplied material inside the hood (e.g. packets with 
screws (*), guarantees (*), etc.), eventually removing 
them and keeping them. 

  
In the case of the presence of panels and/or walls and/or 
lateral wall units check that there is sufficient space to install 
the hood and that access to the command panel is easy. 

To remove the hood from the wall unit, 

perform the 

mounting steps in reverse order. 

Caution!

 Use suitable cut resistant gloves. 

Start detaching the hood from the double-sided adhesive that 
keeps it adherent to the bottom of the wall unit (see also Fig. 
4) 
Therefore, use a cutter that can be slipped between the sheet 
metal of the hood and the bottom of the wall unit on the right 
and left sides. Fig. A  

Caution

! Otherwise, if you use force during extraction, the 

sheet metal of the hood could be irremediably distorted. 

Operation 

1 ON/OFF 

motor 

Pressing the button, the hood turns on at speed 1. 

Pressing the button during functioning, the hood turns 
OFF. 

2 Speed 

Increase 

Pressing the button the hood passes from the OFF state 
to speed 1. 

Pressing the button (hood in ON state) the motor speed 
is increased from speed 1 to intensive. 

To each speed corresponds the ignition of the respective 
led. 

Speed 1 led 

L1

Speed 2 led 

L2

Speed 3 led 

L3

Intensive Speed led 

L4 

(flashing) 

The intensive speed is timed. The  standard timing is 5’, 
at the end of which the hood positions itself to speed 2. 

To deactivate the function before the time expires press 
key 

2

, the hood positions itself to speed 1, pressing key 

1

the hood will turn off. 

3 ON/OFF 

lights 

4 Speed 

timing 

5  Function state indicator 

Speed Timing 

The timing of the speed is enabled by pressing key 

4

, once 

the timing expires the hood turns off. 
The timing is subdivided as follows: 
Speed 1 - 20 minutes (led 

L1

 flashing) 

Speed 2 - 15 minutes (led 

L2 

flashing) 

Speed 3 - 10 minutes (led 

L3

 flashing) 

Intensive Speed - 5 minutes (led 

L4

 flashing) 

 
During the timed functioning pressing key 

1

 the hood turns off, 

if you press key 

2 

or key

 4

 the hood returns to the set speed. 

Grease trap Signal 

After 40 hours of operation the led 

L5

 turns on. 

When such signal appears the installed grease trap needs to 
be washed. 
To reset the signal hold down key 

1

 for 3”. 

Carbon filter Signal 

After 160 hours of operation the led 

L5

 flashes. 

When such signal appears the installed carbon filter must be 
substituted. 
To reset the signal hold down key 

1

 for 3”.  

 
In the case of both filters signalling at the same time, the led 

L5 

will indicate the alarms alternately remaining on for 3" and 

subsequently flashing 3 times. 
The reset takes place by carrying out the procedure described 
above 2 times. 
The first time resets the grease trap signal, the second resets 
the carbon filter signal. 
 
In the standard mode the carbon filter signal is not active. 
In case one uses the hood in filter version is it necessary to 
enable the carbon filter signal. 
 

Carbon filter signal activation: 

Position the hood in OFF and simultaneously hold down keys 

1

 and 

4

 for 3”. 

The led 

L1

 and 

L2

 will flash for 5”. 

Carbon filter signal deactivation: 
Position the hood in OFF and simultaneously hold down keys 

1

 and 

4

 for 3”. 

The led 

L1

 will flash for 2”.