Вытяжки Elica FLIRT IX/A/90/TC - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
18
To each speed corresponds the ignition of the respective
led.
Speed
1:
1
Speed
2:
2
Speed
3:
3
3 ON/OFF
lights
4 Speed
timing
5 Function state indicator
Speed Timing
The timing of the speed is enabled by pressing key
4
, once
the timing expires the hood turns off.
The timing is subdivided as follows:
Speed 1 - 20 minutes (
1
fixed, flashing
point
)
Speed 2 - 15 minutes (
2
fixed, flashing
point
)
Speed 3 - 10 minutes (
3
fixed, flashing
point
)
During time-running, if key
1
or
4
is pressed, the hood turns
off; if key
2
is pressed,
the hood
stops
time-running and sets
to the selected speed.
Grease filter signalling
The grease filter is signalled by the display with number 1
flashing after 80 hours of use.
This means that the grease filter needs to be washed.
The signalling is visible with the hood in
ON
state.
To eliminate the grease filter signalling, press key
“1”
for
more than 3”, until it turns off.
The signalling can be eliminated with the hood in
ON
state.
Carbon filter signalling (only for filtering version)
The carbon filter is signalled by the display with number 2
flashing after 320 hours of use.
This means that the grease filter installed must be replaced.
The signalling is visible with the hood in
ON
state.
To eliminate the carbon filter signalling, press key
“1”
for
more than 3”, until it turns off.
The signalling can be eliminated with the hood in
ON
state.
In case both filters are signalled at the same time, numbers 1
and 2 flash on the display alternately.
The signalling can be reset by carrying out the above-
described procedure twice.
First it resets the grease filter signalling, then the carbon filter
signalling.
In the standard mode the carbon filter signalling is not active.
In case the filtering version hood is used, it is necessary to
enable the carbon filter signalling.
Activation of carbon filter signalling:
Set the hood to
OFF
and keep keys
“2”
and
“3”
pressed
contemporaneously for 3”.
Numbers 1 and 2 flash alternately for 2”.
Deactivation of carbon filter signalling:
Set the hood to
OFF
and keep keys
“2”
and
“3”
pressed
contemporaneously for 3”.
Number 1 flashes for 2”.
Temperature Alarm
The hood is equipped with a temperature sensor which
activates the motor at speed 3 in case the temperature in the
display zone is too high.
The alarm condition is indicated by the display with the letter
"t"
flashing.
This condition remains as such until the temperature falls
below the alarm threshold.
This mode can be quit by pressing key
“2”
.
Every 30” the sensor checks the ambient temperature of the
display zone.
Display Symbols
Symbol State
Speed 1
Speed 2
Speed 3
Speed 1 - 20 minutes
Speed 2 - 15 minutes
Speed 3 - 10 minutes
Grease filter maintenance
Carbon filter maintenance
Grease filter and carbon filter
maintenance
Temperature Alarm
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
