BRAYER BR3360BN - Инструкция по эксплуатации - Страница 4

6

7

en

en

USING THE MULTISTYLER

Use the multistyler for both long hair and hair of 

middle length. 

•  Place the multistyler on a flat steady heat-resistant 

surface. Make sure that the operating elements 

and the outer surfaces do not touch fusible and 

inflammable objects.

• 

Use the unit on healthy undyed and unpermed hair.

• 

If your hair is dyed or permed, use the multistyler 

rarely.

• 

Before styling, wash your hair with shampoo, wipe it 

with a towel, dry with a hairdryer and comb. 

SETTING THE ATTACHMENTS
Before installing the attachments make sure that the 

operation mode switch (7) is set to the position «0», 

and the plug is not inserted into the socket.

• 

Turn the attachment lock (2) until the symbols «

p

» 

and «▼» match.

• 

Install the hair crimper or the tongs attachment 

into the unit body (1) matching the ledges on the 

attachment with the grooves in the attachment lock 

(2). Turn the attachment lock (2) counterclockwise 

until the symbols «▼» match. Make sure that the 

installed attachment is fixed properly.

• 

To remove the attachment, switch the unit off by 

setting the operation mode switch (7) to the position 

«0», unplug the unit and wait until the attachment 

cools down. Turn the attachment lock (2) clockwise 

and remove the attachment.

HAIR CRIMPER ATTACHMENT

•  Put the multistyler on a flat steady and heat-resistant 

surface.

• 

Insert the power plug into the mains socket.

• 

Set the required operation mode with the switch (7), 

the pilot light (6) will light up:

 - «0» — the multistyler is switched off

 - «1» — low heating temperature

 - «2» — high heating temperature

• 

Set the switch (3) to the required position for hair 

straightening or hair crimping.

• 

divide hair into locks about 4-5 cm wide.

• 

Press the handle (5), place a hair lock between the 

heating plates (4), release the handle (5).

WARNING: do not hold the heating plate at one area 

of the hair lock for longer than 2-5 seconds.

• 

If you are using the heating plates (4) for hair 

straightening, slide them throughout the hair lock 

length.

• 

If you are using the hair crimping function, wait a 

little, then press on the handle (5) and move the 

plates (4) to another part of the hair lock.

• 

Straighten/style all hair locks.

•  Cool your hair down before final styling or applying 

hair spray.

• 

Avoid contact of heated surfaces of the attachment 

with your face, neck and other parts of your body.

•  After you finish using the unit, set the operation mode 

switch (7) to the position «0», and unplug the unit. 

Let the unit cool down.

• 

Notes: 

 -

when switching the unit on for the first time, a 

smell from the heating element can appear, this is 

normal and it is not covered by warranty.

 - always switch the unit off and unplug it when 

you’re not using it.

CURLING TONGS ATTACHMENT

• 

Install the tongs attachment and make sure that it is 

fixed properly.

•  Put the unit on the base (9) on a flat heat-resistant 

surface.

• 

Insert the power plug into the mains socket.

• 

Switch the unit on by setting the operation mode 

switch to the corresponding position «1/2», the pilot 

light (6) will light up.

•  Wait until the operating surface (10) of the 

attachment heats up.

• 

Take a hair lock with the free hand.

• 

Press the clamp handle (12) with the other hand, 

place the end of the hair lock on the operating 

surface (10) and release the clamp handle (12). 

Holding onto the tip (11) and the unit body, wind the 

hair lock around the operating surface (10).

•  Wait for a while, then press the clamp handle (12) 

and release the hair lock.

• 

Repeat this procedure on the rest of your hair.

NOTES:

 -

when using the unit for the first time, a foreign 

smell from the heating element can appear — this 

is normal and it is not covered by warranty.

 - avoid contact of hot surfaces of the attachment 

with your face, neck and other parts of your body 

during the unit operation.

 - during breaks in operation, place the unit on the 

base (9) on a flat heat-resistant surface.

 - do not comb the hair right after curling it, let it 

cool down, hair spray should be applied after hair 

curling.

•  After you finish using the unit, switch it off by setting 

the operation mode switch (7) to the position «0», 

and unplug the unit.

•  Put the unit on the base (9) on a flat heat-resistant 

surface and let it cool down completely.

SPIRAL TONGS ATTACHMENT

• 

Install the spiral tongs attachment (13) on the tongs 

operating surface (10).

CLEANING AND MAINTENANCE

• 

Before cleaning unplug the unit and let it cool down 

completely.

• 

do not immerse the unit, power cord and power plug 

of the unit into water or any other liquids.

• 

do not use detergents, abrasives or any solvents to 

clean the unit.

• 

Clean the unit body and the attachments with a soft, 

slightly damp cloth, and then wipe it dry.

STORAGE

• 

Let the unit cool down completely and clean it before 

taking away for storage.