Ariston BLU1 R ABS 50 V - Инструкция по эксплуатации - Страница 55

2.2. Hydraulic connection

Attention! Installation of safety valve Included In the delivery set Is necessary.

Do not install any stop valve between the safety valve and cold water inlet of the water heater and do not block 

the drain hole of the safety valve.

Demountable connectors should be used for the water heater connection to the water supply system.

Standard connection

2.2.1. 

Safety valve (

A

 in Fig. 2) supplied must be installed on the cold water inlet of the water heater (marked with the blue ring).

2.2.2.

 Connect the inlet of the safety valve to the cold water line with a tube or flexible hose.

2.2.3.

 Connect a tube or flexible hose to the hot water outlet of the water heater (marked with the red ring) for hot water

removal to the draw-off point.

2.2.4.

 For easy maintenance, it is recommended to install a T-piece with shut-off (

B

 in Fig. 2) between the cold water inlet and 

safety valve of the water heater.

It will help to drain water from the water heater without safety valve removal.

2.2.5.

 To facilitate the access of air into the tank when draining water, it is recommended to install an additional T-piece with

shut-off valve at the hot water output.

2.2.6.

 When water pressure exceeds 5 bar, place before the safety valve a reducer to reduce the pressure.

2.2.7.

 The device cannot work with water where hardness is less than 12°F. If water is with hardness above 25°F,

it is necessary to use softener to reduce the formation of scale and the probability of failure of the heating element.

The water hardness should not fall below 15°F.

Connection to open tank filled with water

2.2.8.

 Water is supplied to the water heater from the tank by gravity. Safety valve is not necessary in this type of connection.

2.3 Electrical connection

Attention! Electrical wiring should be done by a qualified technician, ensuring it complies with safety rules. The manufacturer is 

not to be held responsiable for any damage caused by the incorrect earthing of system or for fault defaults of electricity supply.

2.3.1. 

If the product is already equipped with a cable and plug, simply connect it to a power supply source.

2.3.2. 

If the water heater is supplied without a power supply cable, use a cable featuring the same characteristics (type

H05VV-F 3x1,5 mm

2

, Ø 8,5 mm) for connection. Remove the cover. The power supply cable should be threaded through the

relevant hole on the cover of the appliance and fixed to the thermostat terminals. Then every wire should be fixed in place

by the corresponding screw.

2.3.3. 

The water heater must be earthed. Grounding scheme should ensure the absence of electric potential on the body

of the water heater. The earth cable (of yellow-green color) should be fixed to the terminal marked by the symbol  .

Fix the power supply cable using the cable clamps.

Make sure that the power supply voltage conforms to the water heater technical characteristics indicated on

the data plate.

2.2. Hydraulic connection

Note! Installation of safety valve included in the delivery set is necessary.

Do not install any stop valve between the safety valve and the inlet of the tank and do not block the drain hole of the 

safety valve.

Demountable connectors should be used for the water heater connection to the water supply system.

Standard connection (Fig. 1)

2.2.1.

 Safety valve supplied must be installed on the cold water inlet of the water heater (marked with the blue ring). It is 

recommended to turn the safety valve no more than 3−4 turns, providing sealing with water-proof sealing material.

2.2.2. 

2.2.3.

2.2.4.

safety valve of the water heater. 

It will help to drain water from the water heater without safety valve removal. 

2.2.5. 

To facilitate the access of air into the tank when draining water, it is recommended to install an additional T-piece with 

2.2.6.

 When water pressure exceeds 5 bar, place before the safety valve a reducer to reduce the pressure.

2.2.7.

 Water is supplied to the water heater from the tank by gravity. For this purpose, the tank water outlet T-piece 

supplying water to the heater and other places must be installed higher than the water heater top. Safety valve is not 

necessary in this type of connection.

2.3. Electrical connection

manufacturer is not to be held responsible for any damage caused by the incorrect earthing of the system or for fault 

defaults of the electricity supply.

2.3.1.

heater.

2.3.2.

 If the water heater is supplied without a power supply cable, use a cable featuring the same characteristics (type 

H05VV-F 3x1,5 mm

2

,  Ø 8,5 mm) for connection. The power supply cable should be threaded through the relevant hole on 

corresponding screw.

2.3.3.

the symbol 

. Fix the power supply cable using the cable clamps. 

2.3.4.

 Make sure that the power supply voltage conforms to the water heater technical characteristics indicated on the data 

plate. 

Flange on the 5 bolts

Indicating light

contacts

Earthing

Power supply

2.2. Hydraulic connection

Attention! Installation of safety valve Included In the delivery set Is necessary.

Do not Install any stop valve between the safety valve and the inlet of the tank and do not block the drain hole 

of the safety valve.

Demountable connectors should be used for the water heater connection to the water supply system.
Standard connection (Fig. 1)

2.2.1. 

Safety valve supplied must be installed on the cold water inlet of the water heater (marked with the blue ring). It is 

recommended to turn the safety valve no more than 3-4 turns, providing sealing with water-proof sealing material.

2.2.2. 

2.2.3. 

2.2.4. 

valve of the water heater.

It will help to drain water from the water heater without safety valve removal.

2.2.5. 

To facilitate the access of air into the tank when draining water, it is recommended to install an additional T-piece with 

2.2.6.

 When water pressure exceeds 5 bar, place before the safety valve a reducer to reduce the pressure.

2.2.8. 

Water is supplied to the water heater from the tank by gravity. Safety valve is not necessary in this type of connection.

2.3. Electrical connection

The manufacturer Is not to be held responsible for any damage caused by the Incorrect earthing of the system 

or for fault defaults of the electricity supply.

2.3.1. 

If the product is already equipped with a cable and plug, simply connect it to a power supply source.

2.3.2. 

If the water heater is supplied without a power supply cable, use a cable featuring the same characteristics (type 

H05VV-F 3x1,5 mm , Ø 8,5 mm) for connection. Remove the cover. The power supply cable should be threaded through the 

by the corresponding screw.

2.3.3. 

The water heater must be earthed. Grounding scheme should ensure the absence of electric potential on the body 

.  

Fix the power supply cable using the cable clamps.

Make sure that the power supply voltage conforms to the water heater technical characteristics indicated on 

the data plate.

28

2.2.7.

 The device cannot work with water where hardness is less than 12°F. If water is with hardness above 25°F,

it is necessary to use softener to reduce the formation of scale and the probability of failure of the heating element.

The water hardness should not fall below 15°F.

GENERAL WARNINGS

1. This manual is included in water heater delivery set. It should be kept alongside the appliance even if the 

latter is transferred to another user and/or moved to another location.

2. Read this manual carefully. It provides important safety precautions for installation, use and maintenance 

of the water heater.

3. The appliance is installed at the expense of the user.

4. The use of the appliance for purposes other than those specified is strictly forbidden. The manufacturer is 

not to be held responsible for any damage due to failure to comply with the instructions set in the manual.

5. All installation and maintenance works must be carried out by a qualified technician in conformity with 

the current rules and regulations, as well as the directions provided by the manufacturer.

6. Incorrect installation can cause personal injury and property damage. The manufacturer is not to be held 

responsible for damage due to incorrect installation.

7. Keep all packing material (clips, plastic bags, polystyrene foam, etc.) out of children's reach. The packing 

material is hazardous for health.

8. The appliance is not intended for use by persons (including children) with reduced physical, sensory, or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for their safety.

9. It is strictly forbidden to touch the appliance barefoot or with wet hands and/or feet.

10. Repair works should be carried out by a qualified technician using original spare parts produced by 

manufacturer. Failure to comply with this requirement invalidates all warranties on the part of the 

manufacturer.

11. The temperature of the hot water is adjusted by a thermostat that acts as a protection against 

overheating.

12. Water supply must be done in accordance with paragraph “Hydraulic Connection”.

13. Electric wiring must be done in accordance with paragraph “Electrical Connection”.

14. It is strictly forbidden to modify or replace the safety valve with the other one which does not meet the 

current rules and regulations, if it is not included in the delivery set.

15. No inflammable items should be kept near the appliance.

16. The water heater is a technically sophisticated electrical appliance for household purposes.

17. Whenever electrical water heater installation involves re-equipment (rearrangement) of residential and 

non-residential premises in residential buildings, installation should be performed only after relevant 

permissions have been obtained in a proper manner.

Before cleaning, isolate the appliance from the mains by 
unplugging it or turning the switch off

10

11

12

Install the appliance on a solid wall that is not subjected to 
any vibrations

Make electrical connections using cables with conductors 
of suitable section

Make sure all control and protection functions operate correctly 
before start the appliance

Electric shock

Excessive noise

Incorrect conductor section results in cables overheating. 
It may cause fire.

Shutdown or damage of the appliance due to out-of-service 
or unregulated control system operation

Before water heater handling, drain hot water

Descale the components in accordance with the instructions 
provided in the applicable document. Air the room. 
Work is performed in protective clothing, avoiding mixing 
different products. The water heater and surrounding 
objects shall be protected against ingress of cleansers

Do not use any insecticides, solvents or aggressive detergents 
to clean the appliance

Burns

Injury due to contact of the skin or eyes with acidic substances, 
inhalation or swallowing of harmful chemical agents.

Damage to the appliance or surrounding objects due to corrosion 
caused by acidic substances

Damage to the plastic and painted parts

GENERAL SAFETY NORMS

Damage to the appliance or any objects underneath it due to the 
object falling off following vibrations

Injury from an object falling off the appliance due to its vibrations

Electric shock in case of cable, plug, or socket damage

Electric shock. Burns due to the contact with overheated 
components. Injuries due to the contact with sharp edges or 
protrusions

Injury from the falling appliance

Damage to the appliance or any objects underneath it due to the 
appliance falling off from its place of installation

Do not climb onto the appliance

Do not leave anything on top of the appliance

Do not use the water heater with a damaged power supply cable

Do not start or stop the water heater by plugging it into or out of 
the wall outlet. Use the power switch for this purpose

Do not open the water heater body

Electric shock from live unsheathed wires under voltage

Ref.                               Warning                                                                              Risk                                           Symbol

1

2

3

4

5

6

7

8

9

Failure to comply with this requirement can result in severe injuries and even death

Failure to comply with this requirement can result in damage to property, plants, or animals

General requirements and safety precautions for use

Symbol                                                                               Meaning

KEY TO SYMBOLS

ADDITIONAL SAFETY RULES

55