Metabo PowerMaxx SSD 12 10.8/12 В - Инструкция по эксплуатации - Страница 11

ENGLISH

en

11

0

= middle position: transportation safety device

(Switch-on lock) set

6.4 Switching on and off

Switching on:

 press the trigger switch (4).

Switching off

: Release the trigger (4).

6.5 Speed / tightening torque

The speed and tightening torque are connected 

directly. The lower the speed, the lower the 

tightening torque.
The tightening torque is influenced in the following 

ways:
1) Preselect maximum tightening torque 

(ONLY for PowerMax SSD 12 

BL

)

You can select between 2 speed/ tightening torque 

settings by pressing the button (6). The maximum 

tightening torques can be found in the table on page 

3 (M

max

).

Button (6) lights up to indicate which setting is 

selected.
no lighting = max. speed / max. tightening torque
permanent lighting = low speed / low tightening 

torque

2) Stepless adjustment of the tightening torque 

(for PowerMax SSD 12 

and

 PowerMax SSD 12 BL)

The speed and tightening torque can be adjusted 

steplessly by pressing the trigger (4) firmly or lightly, 

thus adapting to working conditions. 

Recommendation:

 determine the correct setting 

by carrying out trial screwdriving. 

6.6 Changing the screwdriving bit

Inserting screwdriving bit: 

Slide locking sleeve  

(2) forward and insert screwdriving bit as far as the 

stop. Release locking sleeve (2) . 

Pull on the screwdriver bit to check that it is 

correctly seated.

Removing screwdriving bit: 

Slide locking sleeve  

(2) forward and remove screwdriving bit. 

Only use screwdriving bits with such plug-in 

ends:

The screwdriving bit used must match the 

screw.
Damaged screwdriving bits must not be used.

Mount the machine on the screw, ensuring it is 

aligned straight. 

The screwdriving process consists of 2 parts: 

insert 

screw

 and 

tighten screw with the impact mechanism.

The tightening torque depends on the impact 

duration.

With an impact duration of approx. 5 seconds, the 

maximum tightening torque has been reached.
The torque curve depends on the type of 

application:
With a hard screwdriving application (screw-

couplings in hard material such as metal), maximum 

tightening torque is already reached after a short 

impact duration (a).
With a soft screwdriving application (screw-

couplings in soft material such as wood), a longer 

impact duration (b) is required.
Recommendation: determine the correct impact 

duration by carrying out trial screwdriving. 

Caution!

 For 

small screws 

the maximum torque 

can be reached already after 

0.5 seconds impact duration.
- This is why the duration of the screwdriving 

process must be monitored exactly.

- For PowerMax SSD 12 BL: Use button (6) to set a 

suitable level (see chapter 6.5).

- Adjust the tightening torque by pressing firmly or 

lightly on the trigger (4), ensuring that the screw is 

not damaged or that the screw head does not tear 

off.

Use only original Metabo or CAS (Cordless Alliance 

System) battery packs and accessories.
Use only accessories that fulfil the requirements 

and specifications listed in these operating 

instructions.
See page 4.

A Chargers

B Battery packs with different capacities

Use only battery packs with voltage suitable for 

your power tool.

C Screwdriving bits

For a complete range of accessories, see 

www.metabo.com or the catalogue.

Repairs to electrical tools must ONLY be 

carried out by qualified electricians! 

7. Use

9,5 mm (3/8“)

8. Accessories

9. Repairs