Liebherr WK 6476 - Инструкция по эксплуатации - Страница 3

7

Setting up

•  Avoid positioning the appliance in direct sunlight or near cookers, 

radiators and similar sources of heat.

•  The floor on which the appliance stands should be horizontal and 

level.Compensate for uneven floors with the adjustable feet. 

•  Always ensure that there is good ventilation and that the outward 

flowing air is able to escape.

•  Standard EN 378 specifies that the room in which you install your 

appliance must have a volume of 1 m

3

 per 8 g of R 600a refrigerant 

used in the appliance, so as to avoid the formation of inflammable 

gas/air mixtures in the room where the appliance is located in the 

event of a leak in the refrigerant circuit.  The quantity of refrigerant 

used in your appliance is indicated on the type plate on the inside 

of the appliance.

•  Do not connect the appliance to the supply with other equipment 

using an extension cable - risk of overheating.

Connecting to the mains

Power supply (a.c.) and voltage at the operating point must comply 

with the details on the type plate. The socket must be fused with a 

10 A fuse or higher, it must be away from the rear of the appliance 

and must be easily accessible.

Connect  the  appliance  with  a  properly  earthed  fused  plug 

and socket only. 

The wires in the mains lead are coloured in accordance with the 

following code: green/yellow = earth, blue = neutral, brown = live. 

Warning! This appliance must be earthed.

GB

Dimensions

Operating and control elements

1

Temperature display

2

Temperature setting buttons

3

Audible warning on/off button

4

Fan on/off button

5

Child-proof lock

6

On/off button 

Setting the temperature

To reduce the temperature: 

Press the DOWN button; 

To increase the temperature: 

Press the UP button.

-  While you are entering the temperature, the set temperature will 

flash on the display.

-  You can change the settings in increments of 1°C briefly pressing 

the button again. 

-  The  electronic  controls  will  switch  over  automatically  about  5 

seconds after the last time you pressed the button, and the actual 

temperature will be displayed. 

If 

F  1

  appears  in  the  display,  the  appliance  has  a  fault.  Consult 

your nearest customer service point.

Fan switch

Thereby  a  climate  which  corresponds  to  that  of  a  wine  cellar  is 

achieved inside the wine cooler. Corks are prevented from drying 

out due to an increased level of humidity.

To switch on:

 Press the 

Ventilation

 button. The indicator 

lamp in the switch will light up.

To switch off:

 Press the 

Ventilation

 button. The indicator 

lamp in the switch goes dark.

Switching the appliance on and off

You are recommended to clean the appliance before switching it 

on for the first time (see 

Cleaning

). Connect the appliance to the 

mains - the appliance is switched on.

• To  switch  the  appliance  on:

 Press the 

ON  /  OFF

 button until 

the Display lights  up. 

• To switch the appliance off: 

Keep the 

ON / OFF

 button pressed 

for 3 sec. so that the temperature display goes out. 

Storing wine

If you are storing wine for long periods of time, it should be stored 

at a temperature of between 10°C and 14°C. 
This is the temperature wine cellars are kept at, and it is just right 

to allow wine to mature properly.
The  following  drinking  temperatures  are  recommended  for  the 

various types of wine.
Red wines: 

+14°C to +18°C

Rosé wines: 

+10°C to +12°C

White wines: 

+8°C to +12°C

Sparkling wines, Prosecco

 +7°C to +9°C

Champagne 

+5°C to +7°C

Caution!

The maximum load capacity of the wood racks is 80 kg.