Timberk THU UL 30 E - Инструкция по эксплуатации - Страница 6

www.timberk.com • electric humidifier

6

the --- button to turn off this function.

Timer to turn off the device

To set the timer time to turn off the device, press the button --- several times, 

and the set timer time before the device is switched off will be reflected on 

the display from 1 to 24 hours, in increments of 1 hour. Within 3 seconds 

after setting, the set value will be memorized and will be displayed on the 

display. The device will switch off after the set time interval has elapsed.

Turning off the instrument or setting the timer value [0] will cancel the timer 

to turn off the device.

Automatic operation mode

In automatic operation mode, the steam output intensity will be adjusted 

automatically. If the relative humidity level is less than 40%, the humidifier 

will operate with a high steam output rate. If the relative humidity is between 

40% and 60%, the humidifier will operate at an average steam output rate. 

If the relative humidity level is more than 60%, then the humidifier will work 

with a low vapor yield. To turn this mode on and off, press the --- button. 

When this button is pressed, the mode is switched on / off, the automatic 

mode indicator will light up / go out on the control panel.

Disabling the light indication

In this mode, the display backlight and the light indication of the operating 

modes around the control panel are turned off.  To activate this mode, 

press and hold the --- button for 3 seconds. To turn off this mode, press 

any button.

Automatic shut-off in the absence of water

If the water level in the tank drops below the minimum permissible level, 

the ultrasonic membrane of the device will automatically turn off, an audible 

signal will sound, the indicator will not light on the display, and the light 

indication of the modes around the control panel will glow red.

To continue the operation of the device it is necessary to fill the reservoir 

with water according to item 6 «Filling the reservoir with water», then 

connect the device to the electrical network.

Sound notification

When the appliance is switched on and off, and when the buttons are 

pressed, a beep is emitted.

Switching off the device

To turn off the device, press the button --- and disconnect the device from 

the mains.

IMPORTANT!  

To avoid deformation or wear of working surfaces, 

resulting in decreased atomizing or other malfunctions, do 

not use metallic brushes, blades or talc powder to wipe 

the atomizer’s surface. The water tank may leak upon 

heavy impacts. In case of water leakage, immediately 

stop using the unit and contact a service center. To keep 

the unit dry, remove water after cleaning and make sure 

to dry the unit’s case. Make sure that there is no water left 

inside the unit’s case. Prior to a long break in using the 

unit, dry its surface and pack it into a plastic bag, then 

put it into a box. Store the unit in a low-humidity room. 

Storing the unit undried results in generation of mold

7. CLEANING AND MAINTENANCE

Before cleaning the device make sure that the plug is disconnected from 

the wall outlet. Otherwise, it may result in electric shock. Before cleaning, 

wait until the cooling water in the ground, so as not to burn your hands. 

Spend device cleaning once or twice a week. To clean the outer surface of 

the unit with a damp soft cloth. To avoid electric shock, do not scratch or 

damage the device while cleaning elements.

Do not use when cleaning the device thinner, benzene, dimethyl benzene, 

stiff brush, talcum powder and other materials, except water.

Wipe any remaining water inside the base with a damp, soft cloth.

To remove the remaining water in the small details, you can use a soft 

brush, then wipe it again with a soft cloth.

In the formation of dirt on the membrane, clean it with a soft brushes. Use 

a soft brush to erase the remnants of water on the surface of the device, 

and then wipe it again with a soft cloth. Rinse water tank and a clean water 

dispenser.

After removal of the residual water from the surface of the sprayer, wipe it 

with a soft cloth. Clean the outside surface with a damp, soft cloth.