Утюги VITEK VT-8317 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
5
ENGLISH
•
If an item is made of mixed fabrics, the iron
should be set to the lowest temperature (for
instance, if an item is 60% polyester and 40%
cotton, it should be ironed at temperature used
for polyester ironing «
•
»).
•
If you cannot define the fabric structure, find a
place that is inconspicuous while wearing and
select the ironing temperature experimentally
(always start with the lowest temperature and
raise it gradually until you get the desired result).
•
Corduroy and other fabrics that become
glossy quickly should be ironed strictly in one
direction (in the direction of the pile) with slight
pressure.
•
To avoid appearance of glossy spots on syn-
thetic and silk fabrics, iron them backside.
SETTING THE IRONING TEMPERATURE
•
Place the iron on its base (8).
•
Insert the power plug into the mains socket.
•
Turn the temperature control knob (11) to set the
required ironing temperature: «
•
», «
••
», «
•••
»
or
«MAX»
(depending on the fabric type)
,
the
pilot lamp (9) will light up.
•
Once the temperature of the soleplate (14)
reaches the set point, the pilot lamp (9) will go
out and you can start ironing.
Notes:
–
If you are ironing at high temperature but you
need to switch to lower temperature, wait until
the soleplate temperature decreases and the
pilot lamp (9) lights up, and only then you may
start ironing.
–
While steam ironing it is necessary to set the
ironing temperature «
•••
» or «MAX», the
steam ironing sector is marked with corre-
sponding symbols on the temperature con-
trol knob (11).
WATER SPRAY
•
You can dampen the fabric by pressing the water
spray button (4) several times.
•
Make sure that there is enough water in the
water tank (10).
DRY IRONING
•
Place the iron on its base (8).
•
Insert the power plug into the mains socket.
•
Set the continuous steam supply knob (3) to the
utmost right position – continuous steam sup-
ply is off.
•
Turn the temperature control knob (11) to set the
required ironing temperature: «
•
», «
••
», «
•••
»
or
«MAX»
(depending on the fabric type)
,
the
pilot lamp (9) will light up.
•
When the soleplate (14) reaches the set tem-
perature, the pilot lamp (9) will go out, you can
start ironing.
•
After you finish ironing, set the temperature con-
trol knob (11) to the «OFF» position.
•
Pull the power plug out of the mains socket and
let the iron cool down completely.
STEAM IRONING
While steam ironing it is necessary to set the ironing
temperature «
•••
» or
«MAX»,
the steam ironing
sector is marked with corresponding symbols on the
temperature control knob (11).
•
The iron is provided with an anti-drip valve that
stops water supply if the soleplate temperature
is too low; it prevents dripping from the soleplate
openings (14). During heating and cooling of
the iron soleplate (14), you will hear characteris-
tic clicks of the anti-drip valve opening/closing,
which indicates its normal operation.
•
Place the iron on its base (8).
•
Set the continuous steam supply knob (3) to the
utmost right position – continuous steam sup-
ply is off.
•
Insert the power plug into the mains socket.
•
Make sure that there is enough water in the
water tank (10).
•
Turn the temperature control knob (11) to set the
required ironing temperature:
«
•••
» or
«MAX»
,
the pilot lamp (9) will light up.
•
When the soleplate (14) reaches the set temper-
ature and the pilot lamp (9) goes out, you can
start ironing.
•
Turn the continuous steam supply knob (3) to
set the steam generation rate, steam will start
going out from the soleplate (14) openings.
•
Set the temperature control knob (11) to the
position «OFF», and the continuous steam sup-
ply knob (3) to the utmost right position - con-
tinuous steam supply is off.
•
Pull the power plug out of the mains socket and
let the iron cool down completely.
ATTENTION!
If the steam is not constantly supplied during oper-
ation, check whether the temperature control
knob (11) is set properly and there is water in the
water tank (10).
VT-8317.indd 5
7/5/19 2:26 PM
