VITEK VT-1257 VT - Инструкция по эксплуатации - Страница 4

Утюги VITEK VT-1257 VT - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.

Если остались вопросы, задайте их в комментариях после инструкции.

"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Страница:
/ 24
Загружаем инструкцию
background image

4

 ENGLISH

 •

This  unit  is  not  intended  for  usage  by  people 
(including children over 8) with physical, neural 
and mental disorders or with insufficient expe-
rience  or  knowledge.  Such  persons  may  use 
the unit only if they are under supervision of a 
person who is responsible for their safety and 
if  they  are  given  all  the  necessary  and  under-
standable  instructions  concerning  the  safe 
usage  of  the  unit  and  information  about  dan-
ger that can be caused by its improper usage.

 •

There  may  be  water  residue  in  the  tank,  this 
is  normal,  as  the  iron  has  undergone  factory 
quality control.

 •

Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction 
is  detected  or  after  it  was  dropped,  unplug 
the  unit  and  apply  to  any  authorized  service 
center  from  the  contact  address  list  given  in 
the  warranty  certificate  and  on  the  website 
www.vitek.ru.

 •

Transport the unit in the original package only.

 •

Keep the unit out of reach of children and dis-
abled persons.

THE  UNIT  IS  INTENDED  FOR  HOUSEHOLD  USE 
ONLY,  ITS  COMMERCIAL  USAGE  AND  USAGE 
IN PRODUCTION AREAS AND WORK SPACES IS 
PROHIBITED.

BEFORE THE FIRST USE

After  unit  transportation  or  storage  at  low 
temperature  keep  it  for  at  least  three  hours 
at room temperature before switching on.

 •

Unpack  the  iron;  remove  the  protection  from 
the iron soleplate (15), if any.

 •

Check  the  unit  for  damages;  do  not  use  the 
iron in case of damages.

 •

Before  switching  the  iron  on,  make  sure  that 
your home mains voltage corresponds to the 
iron operating voltage.

 

There  may  be  water  residue  in  the  tank, 
this  is  normal,  as  the  iron  has  undergone 
factory quality control.

Note:  When  the  iron  is  switched  on  for  the 
first  time,  the  heating  element  of  the  iron 
burns, therefore occurrence of foreign smell 
and  a  small  amount  of  smoke  is  possible,  it 
is normal.

WATER SELECTION

This  iron  has  a  built-in  anti-scale  system.  Use 
tap water only to fill the tank (13). Using distilled 

and/or demineralized water decreases the anti-
scale system efficiency.

Note:  Do  not  fill  the  water  tank  (13)  with 
scented  liquids,  vinegar,  starch  solution, 
descaling reagents, chemical agents etc.

FILLING THE WATER TANK

Before  filling  the  iron  with  water,  make  sure  that 
it is unplugged.

 •

Set  the  temperature  control  knob  (11)  to  the 
«

MIN

»  position  and  the  continuous  steam 

supply  knob  (3)  to  the  utmost  left  position  - 
the steam supply is off.

 •

Open the water inlet lid (2). 

 •

Pour  water  into  the  water  tank  (13)  and  then 
close the lid (2) tightly.

Note

 

Do not exceed the «MAX» mark (14).

 

If  you  need  to  refill  water  during  ironing, 
switch the iron off and unplug it.

 

After  you  finish  ironing,  switch  the  iron 
off,  wait  until  it  cools  down  completely, 
then open the water inlet lid (2), turn over 
the iron and drain the remaining water.

IRONING TEMPERATURE

Before operation, test the heated iron on a piece 
of cloth to be sure that the iron soleplate (15) and 
the water tank (13) are clean.

 •

Always check the recommended ironing tem-
perature indicated on the tag before ironing.

 •

If  there  is  no  tag  with  recommended  ironing 
temperature,  but  you  know  the  type  of  fab-
ric,  use  the  following  table  to  determine  the 
proper temperature.

Icons

Fabric type (temperature)

do not iron

synthetics, nylon, acrylic, polyester
(low temperature)

••

silk/wool (medium temperature)

•••

cotton/linen (high temperature)

 •

This  table  is  only  valid  for  smooth  materials. 
Fabrics of other types (crimped, raised, etc.) 
are best ironed at low temperature.

 •

First  sort  items  by  ironing  temperature:  syn-
thetics  to  synthetics,  wool  to  wool,  cotton  to 
cotton etc.

VT-1257.indd   4

07.11.2017   18:06:52

Полезные видео

Характеристики

Оцените статью
tehnopanorama.ru
Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)

Задать вопрос

Часто задаваемые вопросы
Как посмотреть инструкцию к VITEK VT-1257 VT?
Необходимо подождать полной загрузки инструкции в сером окне на данной странице
Руководство на русском языке?
Все наши руководства представлены на русском языке или схематично, поэтому вы без труда сможете разобраться с вашей моделью
Как скопировать текст из PDF?
Чтобы скопировать текст со страницы инструкции воспользуйтесь вкладкой "HTML"