Утюги Saturn ST-CC0214 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
4
IMPORTANT SAFEGUARDS
1. Please read all instructions carefully
before using the appliance for the first
time.
2. Before connecting the appliance,
check if the voltage indicated on the
rating plate corresponds with the mains
voltage in your home.
3. Do not use appliance for other than
intended use.
4. The iron should always be switched
off before connecting or disconnecting
from the power supply. Do not pull on
the cord to disconnect the plug from the
wall socket.
5. Do not use the iron when it is
damaged in any way. Do not operate
the iron with a damaged cord or plug.
Do not replace the power cord or any
other
parts
by
yourself-contact
Customer Support for Assistance.
6. The iron must not be left unattended
while it’s connected to the supply mains.
7. The iron must be removed from the
socket outlet before the water reservoir
is filled with water (for steam irons
incorporating
means
for
spraying
water).
8. The iron must be used and rested on
stable surface.
9. When placing the iron on it’s stand,
ensure that the surface on which the
stand is placed is stable.
10. The iron is not to be used if it has
been dropped, if there are visible signs
of damage or if it’s leaking.
11. This appliance is not intended for
use by persons (including children) with
reduces physical, sensory or mental
capabilities or lack of experience and
knowledge, unless they have been given
supervision or instruction. It is not
advised to use this appliance by children
under 14.
12. Children should be supervised to
ensure that they do not play with the
appliance.
SPRAYING
This function can be used any time and
it
does
not
affect
the
ironing
temperature.
·
Fill water into the iron.
·
Aim the nozzle towards the garment.
·
Press the spray button.
STEAM IRONING
This function can be used only at higher
ironing temperature.
• • for moderate steam
• • • or MAX for maximum steam
·
Fill water into the iron.
·
Stand the iron upright.
·
Connect he iron to a suitable mains
supply outlet
·
Turn the temperature control button
to the “• • ”, or “• • •” "MAX" setting
·
The pilot light turns on when the
required temperature is reached. The
iron is ready for use.
·
Turn the steam knob to the required
position, steam starts coming out from
the holes in the sole plate.
Notice:
With
conventional
steam
ironing, water may leak from the sole
plate if too low temperature has been
select. If this happens turn the
temperature control to the advised
position. Steam will recommence as
soon as die appropriate temperature has
been reached.
BURST OF STEAM
This function provides an extra amount
of steam to remove stubborn wrinkles.
·
Fill the iron with water.
·
Turn the temperature control to the
position 'MAX".
·
The iron is ready for use.
·
Press the burst of steam knob once
·
Steam will penetrate into the
garment removing the wrinkles.
·
Wait a few seconds before pressing
the steam control knob wrinkles again
when there are stubborn wrinkles.
Usually all wrinkles can be removed
within three pressings.
DRY IRONING
·
Connect the iron to a suitable mains
supply outlet.
·
Ensure that the steam control knob
is in position “0”.
·
Select
the
setting
on
the
temperature control.
·
When the pilot light turns off, the
required temperature is reached. The
iron is ready to use.
TO LET THE IRON HEAT UP AGAIN
Pick up the iron or move it slightly.
The red shot-off pilot goes out. If the
temperature of the soleplate drops
below the set ironing temperature, the
temperature pilot goes on.
If the pilot light goes on after you have
move the iron, wait for it to go out
before you start ironing.
If the pilot light does not go on after
you move the iron, the soleplate still
has right temperature and iron is ready
for use.
SELF CLEAN FUNCTION
The Self Clean function can remove any
scale or impurities.
Use the self-clean function once every
two weeks. If the water in your area is
5
very hard, the self-clean function should
used more frequently.
·
Make
sure
the
appliance
is
unplugged.
·
Set the Variable steam control knob
to position "0" (=no steam).
·
Fill the water tank to the maximum
level.
·
Select
the
maximum
ironing
temperature.
·
Put the plug in the wall socket.
·
Unplug
the
iron
when
the
temperature pilot light has gone out.
·
Hold the iron over the silk, press and
hold die self-clean button and gently
shake the iron. (Steam and boiling
water will come out of the soleplate.
Impurities and flakes (if any) will be
flushed out.)
·
Release the self-clean button as soon
as all water in the tank has been used
up.
·
Repeat the self-clean process if the
iron still contains a lot of impurities.
CARE AND CLEANING
1. Turn the Temperature Control Dial to
OFF, then disconnect the iron from the
wall outlet and cool it down completely.
2. Deposits and other residues on the
sole plate can be removed with a cloth
soaked in a vinegar/water solution.
3. The casing may the wiped with a
damp cloth and then polished with a dry
one.
4. Never use any abrasives to clean the
sole plate.
5. Keep the sole plate smooth, avoid
contact with metal objects.
6. When you have finished ironing or
you are leaving iron unattended:
- turn the steam control knob to
position “0”.
- stand the iron upright
- disconnect the iron from the wall
outlet
7. Do not allow children to touch the
iron or the power cord whom ironing.
8. Do not immerse die iron or the cord
into water or any other liquid.
9. Do not touch hot metal parts, hot
water or steam. These parts become hot
and may cause burns. Take care if you
turn die iron upside downs: there may
be not hot water in the tank. The plug
and cord should not be allowed to touch
the hot sole plate. Let the iron cool
down completely before taking it away.
Roll the power cord around the iron for
storage.
10. Disconnect die iron from the wall
outlet for filling in water or when you
remove the water after use.
11. The iron is for household use only.
12. Save the instruction manual for
future reference
Notes:
·
Some parts of the iron have been
slightly greased and as result the iron
may smoke slightly when switched on
for the first time. It will not happen
again after a few uses.
·
Before using for the first time,
remove any protective films or stickers
from the sole plate and the cabinet.
Then clean the sole place with a soft
cloth.
·
When using the iron for the first
time, test it on an old piece of fabric.
HOW TO FILL IN WATER
·
Set the Steam Control Knob “0” and
the temperature Control Dial to OFF.
·
Unplug the iron from the wall outlet.
·
Pour water into the water inlet.
·
Fill up to the maximum level “MAX”
of the water tank.
LABEL
KIND OF
TEXTILE
FIBRE
MATERIAL
Synthetic
Acrylic
Modacryc
Polypropylene
Po|yurethane
Synthetic
Acetate
Triacetate
Synthetic
Cupro
Polyamide
(Nylon)
Polyester
Viscose(Rayon)
Silk
Silk
Wool
Wool
Cotton
Cotton
Linen
Linen
SETTING THE TEMPERATURE
·
Insert the plug in the wall socket
and stand the iron upright.
·
Turn the temperature control knob
to the desired temperature setting.
·
The desired temperature has been
reached when the pilot light has turned
off.
The pilot light will turn on and off from
time after time, indicating that the
selected
temperature
is
being
maintained.
