Braun SI 7062 BL - Инструкция по эксплуатации - Страница 11

(A) Start ironing

Filling the water tank

• 

Make sure that the appliance is switched 

off and unplugged.

• 

Fill the water tank with tap water by 

holding the iron slightly inclined, taking 

care not to exceed the  “max” level. If you 

have extremely hard water, we recom-

mend that you use a mixture of 50 % tap 

water and 50 % distilled water.

•  Attention: 

Never use distilled water 

exclusively. Do not add any additives (e.g. 

starch). Do not use condensation water 

from a tumble dryer.

Ironing with steam 

• 

Place the iron on its heel rest (10) and 

plug in.

• 

Select a temperature (7) which is suitable 

for the garments (refer to the garment 

guide on the heel rest). The iron starts to 

heat up and the temperature control LED 

(8) on the iron is on. The anti-drip function 

is automatically activated to prevent water 

leakage at low temperature settings.

• 

Once the selected temperature is 

reached, the temperature control LED 

turns off.  

Steam options:

•  Continuous steam (normal) 

Select the steam quantity by turning the 

steam regulator (4) in a range from «1» to 

«6». We recommend a medium steam 

setting for regular ironing. Only when 

ironing tough fabrics like linen, thick 

cotton or jeans it is recommended to use 

the maximum steam setting 

Note: 

While ironing, do not turn the steam 

regulator beyond setting «6». 

•   Continuous steam (turbo)

When the steam regulator is positioned 

anywhere between «0» and «6» it is 

possible to activate the turbo function by 

pressing the turbo steam button (5) in 

order to emit the highest steam output 

and remove stubborn creases. Press the 

turbo steam button for not more than 1 

minute. 

•   Steam  shot

Prior to use, press the steam shot trigger 

(6) 3 to 4 times to activate it.  

For a powerful boost of steam, press the 

steam shot trigger at intervals of a few 

seconds. 

The temperature selector should have a 

minimum temperature level 3 (

•••

). 

It is possible to use the steam shot 

function by holding the iron in a 

vertical 

position

 and pulling the steam shot 

trigger. This is useful for removing creases 

from hanging clothes, curtains etc.

Spray function 

The spray function (3) produces a fine mist 

that evenly moistens the fabric and makes it 

easier to iron out creases on very tough 

textiles. 

Dry ironing

Set the steam regulator (4) on position «0» 

(= steam off). 

3D soleplate

The unique round shape of the 3D soleplate 

ensures best gliding results on difficult parts 

(e. g. buttons, pockets etc.) and in all 

directions – even backwards.  

(B) Auto off

For safety and reduced power consumption, 

the auto-off function is automatically 

activated when the iron is positioned 

horizontally on its soleplate for about 30 

seconds or vertically on its heel rest for 

about 8 minutes. 

• 

When the iron is in the auto-off mode the 

temperature control LED (8) is blinking.

• 

To turn the iron on again, just move it 

forward. 

• 

Before start ironing again wait until the 

temperature control LED is turned off.

(C) After ironing 

• 

Unplug the iron and empty the water tank.

• 

Let the iron cool down before storing. 

(D) Descaling 

Preparation

1.  Set the steam regulator (4) on position 

«0» (= steam off).

2.  Fill the water tank. 

3.  Plug in and set the temperature at “max“ 

on the temperature selector (7).

4.  Wait until the temperature control LED 

(8) turns off and unplug the iron. Hold 

the iron over the sink.

5.  Turn the steam regulator clockwise 

beyond steam stetting «6». When you 

hear a click pull it out vertically until the 

end of the spring appears. It must not be 

removed completely.   

9

DLB253489_5712710601_SI7_UI_INT.indb   9

21.12.16   09:51