Braun SI 3055 Bk TexStyle 3 - Инструкция по эксплуатации - Страница 10

10

C  Ironing

1 + 2 Variable steam

You can select the steam quantity using the steam 
regulator (6) (  = no steam, 1 = minimum steam, 
2 = maximum steam). The temperature selector 
must be set between «

•••

» and «max».

3 Dry ironing

Set the steam regulator (6) on position   (= steam 
off).

4 Spray function

Press the spray button (5).

5 Steam shot function

Steam shot can be activated when dry ironing. 
The temperature selector must be set between 
«

•••

» and «max».

To obtain a good steam jet, wait a few seconds 
between one shot of steam and the next. 
The steam shot function can also be used in the 
vertical position for steaming hanging clothes.

D Auto-off 

(certain models only)

The orange «auto-off» light (8) will flash when the 
automatic shut-off is activated. This happens when 
the iron is left unused: 

–  horizontally on its sole plate for about 30 seconds 

or

–  vertically on its heel rest for about 8 minutes. 

To begin ironing again, shake the iron slightly 
forwards until the light (8) comes on steadily

E Self cleaning

Over time, the lime in the water causes scale to 
build up inside the iron. To prevent the scale 
reducing steam production, you should perform 
the «self clean» procedure every two weeks.
1.  Place the steam regulator on « » and fill the 

water tank. 

2.  Plug the appliance into the mains and place the 

temperature selector in the «max» position.  
The pilot light is on.

3.  The pilot light turns off (the iron is at tempera-

ture).

4.  Unplug the appliance from the mains. 
5.  Hold the appliance over a sink, press the self 

clean button (11) and, holding the button down, 
shake the iron delicately forwards and backwards. 
Residues of scale and other impurities mixed 
with boiling water come out of the sole plate. 
Release the Self Clean button when the water 
tank is empty.

6.  Plug the appliance into the mains socket and 

leave in operation for at least two minutes to dry 

the sole plate. Unplug the appliance from the 
mains socket. 

7.  Move the sole plate over a cloth to remove any 

residues. 

8. 

Never use steel wool, abrasive scouring 
pads, powders or other chemicals to clean 
the sole plate.

9.  Leave the iron to cool down completely, then 

store away. 

After ironing

Unplug the iron and turn the steam regulator to 
position «   ». 

To prolong the life of the iron, 

empty the water tank.

 Store the cool iron in a dry 

place always standing on its heel rest.

Maintenance and cleaning

To prevent damaging the sole plate, do not iron over 
metal buttons or zippers. 
Clean the sole plate regularly with a damp cloth. 
To remove mineral/starch residues, use a vinegar/
water mixture in the ratio of 1 : 2. Never use steel 
wool, abrasive scouring pads, powders or other 
chemicals to clean the sole plate.
Do not use commercial decalcifiers, they may 
damage the iron.

Trouble -shooting guide

Problem

Remedy

Drops coming out 
of the steam vents

Select steam regulator to 
pos. «1» or turn the steam off. 
Take longer intervals when 
pressing the steam shot 
button.
Select a higher temperature 
setting.

Less steam 
develops or no 
steam at all

Check water level. 
Perform self cleaning 
procedure (E). 

Calcium particles 
coming through 
the steam vents

Perform Self Cleaning 
procedure (E).

Subject to change without notice.

Please do not dispose of the product in the 
household waste at the end of its useful life. 
Disposal can take place at a Braun Service 
Centre or at appropriate collection points 
provided in your country.

1271015IDL_TS_345-355A_S6-64.indd   10

13.05.15   14:31