Утюги Bosch TDS 2011 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
14
B O S C H
EN
G
LI
SH
• This appliance is to be connected and used in
accordance with the information stated on its
characteristics plate.
• This appliance must be connected to an earthed
socket. If it is absolutely necessary to use an
extension cable, make sure that it is suitable for
16A and has a socket with an earth connection.
• If the safety fuse itted in the appliance blows, the
appliance will be rendered inoperative. To restore
normal operation the appliance will have to be
taken to an authorised Technical Service Centre.
• In order to avoid that, under unfavourable mains
conditions, phenomena like transient voltage
drops or lighting luctuations can happen, it is
recommended that the iron is connected to a
power supply system with a maximum impedance
of 0.27Ω . If necessary, the user can ask the
public power supply company for the system
impedance at the interface point.
• The appliance must never be placed directly
under the tap to ill the water tank.
• Unplug the appliance from the mains supply after
each use, or if a fault is suspected.
• The electrical plug must not be removed from the
socket by pulling the cable.
• Never immerse the iron in water or any other luid.
• Do not leave the appliance exposed to weather
conditions (rain, sun, frost, etc.)
Important :
• This appliance reaches high temperatures and
produces steam during use, this could cause
scalds or burns in case of improper use.
• The steam hose, base station and in particular the
iron can get hot when used.
• Never aim the steam at people or animals.
• Do not allow the power cable to come into contact
with the soleplate when it is hot.
Description
1. Water tank
2. Removable iron pad
3. Steam hose storage ixing
4. Carrying handles
5. Mains cable storage compartment
6. Mains cable
7. Steam hose
8. “Steam ready” pilot light
9. “Reill water tank” pilot light *
10. “on / off” pilot light *
11. Main power switch (0/I)
12. Housing with internal steam generator
13. Temperature control knob
14. Steam release button
15. Steam release button “Ultimate Steam”
*
16. Iron pilot light
17. Steam button lock *
18. Soleplate
* Model dependent
A
Preparations
1. Remove any label or protective covering from the
soleplate.
2. Place the appliance horizontally on a solid, stable
surface. You may remove the iron pad from the
appliance and place the iron on it on another
solid, stable, horizontal surface.
3. Fill the water tank, making sure not to pass the
level mark.
4. Unwind the mains cable (6) fully and plug it into
an earthed socket.
5. Set the main power switch (11) to the “I” position.
6. The “Steam ready” indicator lamp (8) will light up
after several minutes, indicating that the appliance
is ready to use.
The steam generator will take more time to reach
“Steam ready” state only upon the initial heating
up, or after performing the de-scaling operation
(Calc’n clean).
When water is already present in the steam
generator during regular use, heat up time to
reach the operating temperature will be faster.
7. This appliance has a built-in water level sensor.
The “reill water tank” indicator (9*) will light when
the water tank is empty.
or (model dependent):
If the “steam ready” lamp (8) lights and steam is
not released when pressing the steam release
button (14, 15*), reill the water tank.
