Триммеры EFCO DSH 400 T ES 61459011E1B - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
5
GB
snap (F, Fig.10).
5. Adjust the carrying height by shortening or
lengthening the belt straps (E, Fig.10). The
correct distance between the belt and the
snap can be measured as in Fig.8. This
adjustment will also help to distribute the
weight of the brushcutter so that it stays
comfortably balanced during operation.
5. STARTING
FUELING
WARNING: Gasoline is an extremely
flammable fuel. Use extreme caution when
handling gasoline or fuel mix. Do not smoke
or bring any fire or flame near the fuel or the
unit.
·
To reduce the risk of fire and burn injury,
handle fuel with care. It is highly flammable.
·
Mix and store fuel in a container approved for
gasoline.
·
Mix fuel outdoors where there are no sparks or
flames.
·
Select bare ground, stop engine, and allow to
cool before refueling.
·
Loosen fuel cap slowly to release pressure and
to keep fuel from escaping around the cap.
·
Tighten fuel cap securely after refueling. Unit
vibration can cause an improperly tightened
fuel cap to loosen or come off and spill
quantities of fuel.
·
Wipe spilled fuel from the unit. Move 3 metre
away from refueling site before starting
engine.
·
Never attempt to burn off spilled fuel under
any circumstances.
·
Do not smoke while handling fuel or while
operating the unit.
·
Store fuel in a cool, dry, well ventilated place.
·
Never place the machine in a combustible
area such as dry leaves, straw, paper, etc.
·
Store the unit and fuel in an area where fuel
vapors cannot reach sparks or open flames
WARNING – Collar (see arrows C, Fig.7)
must locate in blade’s mounting hole.
FITTING THE HANDLE (Fig. 2)
Fit the handle onto the shaft arm and secure it
using screws (A). The handle position is calculated
depending on the requirements of the operator.
WARNING - Assemble the loop handle
(D, Fig.2) between label’s arrow (B) and rear
handle (C).
FITTING THE HANDLEBAR (FIG.5)
- Loosen the clamp screws (D).
- Insert the 2 halves of the handlebar in the
respective sockets (E).
- Retighten the screws (D)
W A R N I N G : M a k e s u r e t h a t a l l
components are connected properly and all
screws tightened.
PREPARING TO WORK
HARNESS (3S, Fig. 1)
Correct adjustment of the harness permits the
brush cutter to be properly balanced and at an
appropriate height from the ground (Fig. 8).
- Put on the single harness.
- Hook the brush cutter to the harness using the
hook (A, Fig. 8).
- Position the hook (18, Fig. 1) to obtain the best
brush cutter balance.
- Position the buckle to obtain the correct brush
cutter height.
CORRECT ADJUSTMENT OF THE HARNESS
BCH 40 T - DSH 400 T models
1. Put on the double harness (3T, Fig.1).
2. Adjust the shoulder straps by means of the 2
buckles (D, Fig.9). With this type of harness, the
weight of the machine can be distributed
between shoulders and waist according to the
preference of the operator.
3. Attach the guard by means of the 2 clasps
(E, Fig.10).
4. Hook the brushcutter to the harness with the
