Sharp LC-55SFE7452E - Инструкция по эксплуатации - Страница 18

EN

*



TV buttons & Source menu

Vol+

Volume up and menu right

Vol-

Volume down and menu left

CH+

Programme/Channel up and menu up

CH-

Programme/Channel down and menu down

MENU

Displays Menu/OSD

SOURCE

Displays the input source menu

STANDBY

Standby Power On/Off 



Choosing Mode Input/Source

To switch between the diff erent input/connections.

a) Using the buttons on the remote control:
1. 

Press [SOURCE/ AV ] - The source menu will appear.

2. 

Press [

▼

] or [

▲

] to select the input you require.

3. 

Press [OK].

b) Using the buttons on the Television:
1. 

Press [SOURCE].

2. 

Scroll up / down using CH+/ CH- buttons to the input/source you 
require.

3. 

Press Vol+ to change input/source to the one selected.



Connections

Please see the table for connector types for 
diff erent models available on the page 24.

USB

USB-Input 1, 2

HDMI 1, 2, 3(MHL) in

HDMI-Input 1, 2, 3

VGA(PC)

VGA PC-Input

VGA (PC) Audio In

3.5mm PC audio input

Mini AV

Video Input & Component / Video audio input

Mini YPbPr

Mini Component HD Input

SCART

SCART-Input

CI Card IN

CI input

RF In

RF / TV Aerial Input

Sat In

Satellite Input

Digital Optical Audio Out 

Digital optical output

RJ 45 

Ethernet 

HEADPHONES

3.5mm Headphone output



TV Menu navigation

To access this menu, press [MENU] button on the remote control. To enter 
a menu press [OK]. If you wish to make changes to any of the default 
settings, use the scroll (

▲/▼/◄/►) 

buttons. To confi rm any settings press 

[OK] button. To exit this menu at anytime, press [EXIT ] button.



Picture

Picture Mode

- Choose from the following presets.

–

Standard 

- Default settings

–

Dynamic 

- Recommended settings for fast moving pictures

–

Mild 

- Set to be lighter in colour and less bright

–

Personal 

- Lets you manually alter all the settings

–

Eco 

- Consume 15% less energy.

Contrast 

- Switch the balance between black and white.

Brightness 

- Increase or decrease the brightness of the picture.

Tint 

- Lets you increase or decrease the level of tint 

within the picture (for NTSC signal only)

Colour 

- Increases the colour from black and white.

Sharpness 

- Increase or decrease the sharpness of the picture.

Backlight adjusting 

- Adjust the screen's brightness by 

increasing/decreasing the panel's backlighting.

Backlight adjusting 

- Adjust the screen's brightness by 

increasing/decreasing the panel's backlighting.

Colour Temperature 

- Choose from the following presets.

–

Normal 

- Default settings

–

Warm 

- Increases red within the picture

–

Cold 

- Increases blue within the picture

Red 

- Adjust red tone of the picture

Green 

- Adjust green tone of the picture

Blue 

- Adjust blue tone of the picture

Gamma 

- Adjust the tones between the bright 

and dark parts of the picture.

Aspect Ratio 

- Picture format varies depending on the channel/broadcast.  

There are a number of diff erent options to best meet your needs.

–

Auto

-Automatically displays the best picture format.  

So the picture is in the correct position. May have  
black lines at the top/bottom and/or sides.

–

4:3 

- Displays the 4:3 picture in its original size.  Side 

bars are shown to fi ll the 16:9 screen.

–

16:9 

- Fills the screen with a regular 16:9 signal.

–

Zoom 1/2 

- The picture is the correct proportion  

but zoomed in to fi ll the screen.

–

Dot by Dot (HDMI) 

- Will display the picture in its 

original resolution without any change.

–

Full Screen 

- Stretch signal to fi ll the screen.

Noise Reduction 

- Filters and reduces the 

noise (interference) of the picture

MPEG Noise Reduction 

- Allows you to reduce visible 

interference caused by MPEG compression.

Active Contrast 

- Automatically optimises the ‘backlight’ and 

‘contrast’ of the picture according to the brightness of the screen.

3D Settings

TIP:

 For the best 3D picture eff ect, watch your TV from vertical angle +/- 10°.

3D Type 

- 3D Type- When connecting a 3D product sometimes 

the picture maybe displayed incorrectly; choose from the 
following settings to correct this. You can toggle these 
settings by pressing the ’3D' button on your remote.