Hander HHG-2000K - Инструкция по эксплуатации - Страница 3

3

Hot air gun

CAREFULLY READ THE INSTRUCTIONS BEFORE 

YOU USE THE HOT AIR GUN!

1. ADDITIONAL SAFETY RULES

BEFORE USING THE APPLIANCE:
1.  Check the following:

-  Make sure the voltage of the hot air gun corresponds 

with the power voltage.

-  Are the mains lead and the mains plug in a good 

state: strong, without ravels or damages.

2.  Avoid the use of long extension cables.
3.  Do not use the appliance under moist circumstances.
4.  The metal mouthpiece gets hot. Watch out and do not 

touch the metal mouthpiece.

5.  Prevent damage of the heating element. Do not lock 

or block the mouthpiece.

6.  Do not leave the appliance when switched on.
7.  When the appliance is not in use, it can be put away 

on the collapsible support, which is on the air gun. By 
collapsing this support, the air gun can easy be put 
away on it. The hot air gun now stands on the support 
with the mouthpiece up.

8.  Do not use the appliance for drying hair or for drying 

living human beings in general.

9.  Do not use the appliance in a bath, above water or in 

spaces where easy in

fl

 ammable liquids are used.

Warning! This appliance operates at a temperature 
of 200-600 degrees without

visible signs of this 

temperature (no 

fl

 ames); still there is a chance of 

fi

 re risk. Watch out for the hot air stream from the 

mouthpiece. This air stream can cause burns.

WHEN OPERATING THE APPLIANCE:

1. If you are going to use the hot air gun, vapours and 

gas can be liberated during a short time. This can 
be harmful for your health. Asthmatics can suffer hin-
drance of it.

2.  Before connecting the plug to the mains voltage you 

have to check if the switch is in position “0”.

3. Keep the mains lead always away from the mouth-

piece of the hot air gun.

4. Keep children and animals away from the appliance 

if you are using it.

IMMEDIATELY SWITCH OFF THE APPLIANCE WHEN:

1.  plug and/or cable are defective or damaged;
2.  the switch is defective;
3. you smell or see smoke caused by scorched insula-

tion from the hot air gun.

2. INSTALLATION

You can work manually with this hot air gun or you 

can put it in a vertical position. If you use the vertical 
position the metal suspension bracket of the handgrip 

must also stand vertical for supporting the handgrip on 
the correct place.

3. USING THE APPLIANCE

THE HOT AIR GUN CAN BE USED FOR:

•  plumbing work like tube connections, solder, bowing 

tubes;

•  removing paint, varnish and lacquer without 

fi

 re-risk;

•  quickly drying of appliances which have become wet;
•  drying surfaces for quick repairing;
•  removing self-adhesive labels in a clean way;
•  placing PVC labels;
• blistering after sticking PVC materials can be 

smoothed after heating;

•  easy removing of vinyl carpeting;
•  forming all synthetics with a low temperature among 

which polyethylene and PVC;

•  forming all synthetics with a high temperature among 

which acryl and plexiglass;

•  smelting synthetics, among which matters and foils 

with PVC layer;

•  applying heat shrinking tubes;
• shrink 

wrappers;

•  thawing tubes and engines;
• repairing 

fi

 nishing layers: email of bath and house-

hold appliances;

•  applying epoxy powder cover layers;
•  repairing of ski's, surf-boards and other sports goods;
•  unscrewing too fast 

fi

 xed screws and connections.

4. BEFORE OPERATING

Before you switch on the hot air gun you have to 

search for the right adapter for the mouthpiece and as-
semble it on the mouthpiece if it is still cold.

IMPORTANT: Replace the mouthpiece only:

•  with a stationary engine;
•  when the appliance is disconnected;
•  when the mouthpiece is cold.

5. OPERATION

•  Check if the mains switch is on position 

“0”

 before 

you connect the apparatus;

•  Keep the power voltage always away from the hot air 

stream and the mouthpiece.

Tip: 

If you want to get the best result, test all appli-

ances on a little part of the workpiece.

6. MAINTENANCE

Always disconnect the apparatus before carrying out 
inspection or cleaning. Never use water or other liq-
uids to clean the electrical parts of the hot air gun.

•  Never use easy in

fl

 ammable liquids for cleaning the 

hot air gun, especially for the mouthpiece.

•  Regular maintenance of your hot air gun prevents un-

necessary problems. Keep the ventilation slots of the 
hot air gun clean to prevent overheating.

GB

English