Bosch 0.601.944.302 - Инструкция по эксплуатации - Страница 14

14

 | English 

1 609 929 S53 | (26.11.08)

Bosch Power Tools

en

Safety Notes

Read all safety warnings and all 
instructions. 

Failure to follow the 

warnings and instructions may re-
sult in electric shock, fire and/or 
serious injury.

f

Be careful when working with the power 
tool. 

The power tool produces intense heat 

which can lead to increased danger of fire 
and explosion.

f

Exercise special care when working close to 
inflammable materials. 

The hot air jet or the 

hot nozzle can ignite dust or gases.

f

Do not operate or work with the power tool 
in areas where there is danger of explosion.

f

Never direct the hot air jet at the same po-
sition for longer periods. 

Easily inflammable 

gases can develop e. g., when working plas-
tic, paint, varnish or similar materials.

f

Be aware that heat can be conducted to hid-
den covered materials and can ignite them.

f

After using, place the power tool down in a 
secure manner and allow it to cool down 
completely before packing it away. 

The hot 

nozzle can cause damage.

f

Do not leave the switched-on power tool un-
attended.

f

Store idle power tools out of the reach of 
children. Do not allow persons unfamiliar 
with the power tool or these instructions to 
operate the power tool. 

Power tools are 

dangerous in the hands of untrained users.

f

Do not expose the power tool to rain or wet 
conditions. 

Water entering a power tool will 

increase the risk of electric shock.

f

Do not abuse the cord. Never use the cord 
for carrying, pulling or unplugging the 
power tool. Keep cord away from heat, oil, 
sharp edges or moving parts. 

Damaged or 

entangled cords increase the risk of electric 
shock.

f

Always wear safety goggles. 

Safety goggles 

will reduce the risk of injuries.

f

Disconnect the plug from the socket outlet 
before making any adjustments, changing 
accessories, or placing the power tool 
aside. 

This safety measure prevents uninten-

tional starting of the power tool.

f

Check the power tool, cord and plug each 
time before use. Do not use the power tool 
if damage is determined. Do not open the 
power tool yourself and have it serviced 
only by a qualified repair person using only 
original spare parts. 

Damaged power tools, 

cords and plugs increase the risk of electric 
shock.

Provide for good ventilation of 
your working place. 

Gas and va-

pour developing during working 
are often harmful to one’s health.

f

Wear safety gloves and do not touch the hot 
nozzle. 

Danger of burning.

f

Never direct the hot air jet against persons 
or animals.

f

Do not use the power tool as a hairdryer. 

The hot air being blown out is significantly 
hotter than that from a hairdryer.

f

When operating the power tool in damp 
environments is unavoidable, use a residual 
current device (RCD). 

The use of a residual 

current device (RCD) reduces the risk of an 
electric shock.

f

Products sold in

 GB only

: Your product is 

fitted with an approved 13 A (BS 1363/A) 
electric plug and is protected by a 13 A fuse 
(ASTA Approved to BS 1362).
If the plug is not suitable for your socket out-
lets, it should be cut off and an appropriate 
plug fitted in its place by an authorised 
customer service agent.
The severed plug must be disposed of to 
avoid a possible shock hazard and should 
never be inserted into a 13 A socket else-
where.

OBJ_BUCH-485-002.book  Page 14  Wednesday, November 26, 2008  1:56 PM