Ariston AD 1000 - Инструкция по эксплуатации - Страница 26

                                              - 

Instructions for installation and use

Model

AD 1000

Dimensions

width 59,5 cm
height 85 cm

depth 53,5 cm

Capacity

from 1 to 5 kg

Electrical

connections

voltage 220/230 Volt 50 Hz
maximum absorbed power 1850 W

Water

connections

maximum pressure 1 MPa (10 bar)
minimum pressure 0,05 MPa (0,5 bar)

drum capacity 46 litre

Spinning speed

up to 1000 rpm

Control programs

in compliance
with IEC
regulation 456

Turn the knob completely to the left and select a temperature of 60°C.

Carried out with 5,0 kg load.

This appliance conforms with the following E.E.C. directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications

The washing machine
does not drain or spin.

Is the “Easy iron"  function
s e l e c t e d ?  

Complete the

programme by pressing the 
button.

Is the drain pump clogged?

To check it, close the tap,
unplug the washing machine
and follow the instructions on
page 25, or call for technical
assistance.

Is the drain hose bent? 

The

tract of the drain hose must be
as straight as possible. Make
sure it is not squashed or bent.

Is the washing machine’s
drain duct clogged? 

Is there

an extension of the drain
hose? If so, is it positioned
incorrectly, blocking the water
flow?

The washing machine
vibrates too much
during the spin cycle.

Has the internal floating
u n i t   b e e n   c o r r e c t l y
u n b l o c k e d   d u r i n g
i n s t a l l a t i o n ?  

S e e   t h e

following page on installation
procedures.

Has the washing machine
been levelled correctly?

 The

levelling of the appliance
s h o u l d   b e   c h e c k e d
periodically. In time, the
m a c h i n e   c o u l d   m o v e
imperceptibly. Adjust the feet
and check them with a level.

Is the appliance closed in
between furniture and a
wall?

 If it is not a built-in

model, the washing machine
needs to oscillate a bit during
the spin cycle. A few cm of
space should therefore be left
around it.

The washing machine
leaks.

Is the metal ring of the inlet
hose properly attached?

Close the tap, unplug the
appliance and try tightening its
attachment without forcing it.

Is the detergent dispenser
obstructed? 

Try extracting it

and washing it under tap
water.

I s   t h e   d r a i n   h o s e   w e l l
attached?

 Close the tap,

unplug the appliance and try
tightening its attachment.

Too much foam.

Is the detergent appropriate
for machine washing?

 Check

whether its label reads the
definition “for machine wash”
or “hand and machine wash”,
or other similar indications.

Is the correct amount being
used? 

An excessive amount of

detergent, besides producing
too much foam, does not
guarantee a more effective
wash, and causes scaling in the
internal parts of the appliance.

If ,  d e s p i t e   a l l   c h e c k s , t h e
w a s h i n g   m a c h i n e   f a i l s   t o
f u n c t i o n   a n d   t h e   p r o b l e m
persists , call your nearest
authorised Customer Service
Centre, providing the following
information:
- the type of malfunctioning
- the model type no. (Mod. ....)
-   the serial number (S/N ....)
These indications can be found
on the data plate situated on the
back of the washing machine.

Technical characteristics

Always get

assistance from

authorised

technicians and

always insist on

original spare

p a r t s .

23