Стиральная машина Saturn ST-WM0622 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
18
3. Unhook the drain hose from the rear support and position the end of this hose
and that of the inlet hose in a bowl. Run the spin program.
4. Disconnect the appliance.
5. Screw the inlet hose and reposition the drain hose.
6. When you intend to start the machine up again, make sure that the room
temperature is above 0
0
C.
Troubleshooting guide
Problem
Error Code
Possible Cause
Solutions
The machine
fills overtime.
“Spin”
LED
flickers
1. The water tap is not
open.
2. The drain hose is put
down.
3. The water inlet valve
is damaged.
1. Open the water tap.
2. Hook up the hose.
3. Change the water inlet
valve.
There is a
Door
lock
alarm.
“Rinse”
LED
flickers.
1. The door is not
locked well.
2. Garment is caught
between the door and
the seal.
3. The door lock is
damaged.
1. Lock the door well.
2. Put the garment into
the drum.
3. Change the door lock.
The machine
drains
overtime.
“Rinse”
and
“Spin”
LEDs
flicker.
1. The drain hose is
squashed or kinked.
2. The drain pump
filter is blocked.
3. The drainage system
pipes are blocked.
1. Check the drain hose.
2. Clean the filter.
3. Check the drainage
system and clean it.
Water
overflows the
machine.
/
Water sensor
works
abnormal.
“Washing”
LED
flickers.
1. The water inlet valve
is damaged.
2.
The
connection
between
the
water
sensor and wire is not
secure.
3. The water sensor is
damaged.
1. Change the water inlet.
2. Check the connection
and ensure it is secure.
3. Change the water
sensor.
19
The
motor
does
not
work.
“Washing”
and
“Spin”
LEDs
flicker.
1.
The
connection
between the motor and
wire is not secure.
2.
The
motor
is
protected because of
over-heat.
3.
The
motor
is
damaged.
1. Check the connection
and ensure it is secure.
2. Check if the machine
is overloaded. Switch off
the machine, and retry
when the motor becomes
cool.
3. Change the motor.
There is a
heating tube
fault.
“Washing”
and
“Rinse”
LEDs
flicker.
1.
The
connection
between the heating
tube and wire is not
secure.
2. The heating tube is
damaged.
1. Check the connection
and ensure it is secure.
2. Change the heating
tube.
There is a
temperature
sensor fault.
“Washing”,
“Rinse”
and
“Spin”
LEDs
flicker.
1.
The
connection
between
the
temperature sensor and
wire is not secure.
2. The temperature
sensor is damaged.
1. Check the connection
and ensure it is secure.
2.
Change
the
temperature sensor.
Note:
Data can vary from the nominal values given depending on water pressure, water
hardness, water inlet temperature, room temperature, type and volume of load,
fluctuations in the electricity supply and any extra options selected.
Symbol explanation
V
Volt
ࡱ
Alternating
current
W
Watt
Hz
Hertz
Safe test
CE symbol
