Oursson JM3400/RD - Инструкция по эксплуатации - Страница 7

7

NOTE: 

Colored scurf on plastic parts of the juice maker, 

for example from the carrot juice or beet juice can be 

removed with a little vegetable oil. Than wash the parts 

under the running water.

ClEANINg AND  MAINTENANCE, 

Рiс. С

• 

The juicer must be cleaned after each use.

•  Pulp container, filter insertion, mesh filter, lid, pusher 

and capacity for collecting juice with lid can be washed 

in the dishwasher. Thoroughly dry all parts.

•  Wash the filter mesh under running water using a 

clining brush and dry gently with a cloth.

POSSIBlE PROBlEMS AND SOlUTIONS 

Problem

Solutions

Device does not 

work 

• 

Check whether the power cord is connected to the outlet. If the device is not connected, plug it to the outlet.

• 

Check whether the device is assembled correctly. If not, disassemble and reassemble according to the 

instructions.

• 

If the problem persists, contact an authorized service center OURSSON.

Little juice

•  The various ingredients have different moisture contents.

• 

If the products are not fresh, they lost their juiciness. Put the ingredients in water for 1-2 hours 

to recover.

• 

If you are using ingredients with small seeds, then after few loads their presence can reduce the 

amount of juice. For best results, between preparations disassemble the machine and clean it 

from seeds.

A lot of pulp in the 

juice

• 

With continued juicing and depending on the ingredients, juice may contain much pulp.

• 

To reduce the pulp in the juice, disassemble the juice cup and remove the pulp more often.

•  If the filter or screw is damaged - it can affect the performance and quality of juice. It is 

recommended to replace them

• 

If too much of the ingredients are loaded into the juice maker simultaneously, this can lead to 

frequent stoppages and to a large number of pulp in the juice. Place ingredients slowly and in 

small portions.

Extraneous 

sounds when the 

device is working

• 

Make sure that all parts are correctly assembled. Try to disassemble and assemble the juice 

maker again and listen to the noise.

• 

Do not turn the juice maker without ingredients. 

• 

Check the size of the juicing products. It is recommended to cut large ingredients into small 

pieces so the fit into the feeding chute.

•  Depending on the type or size of various ingredients different noises may occur.

• 

Noise may occur when the juice maker is working on uneven or inclined surfaces. Lace it on a 

flat stable surface.

Pulp is very wet

• 

At the beginning of juicing, the pulp can be wet.

• 

The recovered pulp can be wet if you are using stale ingredients.

• 

Before juicing ingredients stored in the refrigerator for a long time, put them in clean drinking 

water for 1-2 hours.

The device is 

vibrating

• 

A small vibration of juice maker is allowed during operation. It is not considered a malfunction.

The device has 

stopped working

•  Turn off the device and let it cool for 5 minutes. Then turn it on again. 

• 

The device is equipped with an engine overheating protection system, the device will turn on 

after the engine has cooled down.

PRODUCT CERTIFICATION 

For information on product certification, see 

http://www.oursson.com

 or ask seller for a copy.

*Products should be stored in dry, ventilated warehouses at temperatures below - 25°C.

Specifications

Model

JM

3400

Power consumption, W

max 500

Rated voltage

220-240 V~; 50 Hz

Protection class

II

Storage and transportation temperature requirements

-25 °C to +35 °C

Operation temperature requirements

+5 °C to +35 °C

Humidity requirements

15-75% (without condensation)

Dimensions (LxWxH), mm

250x200x370

Weight, kg

2.85

Wipe the device with a damp cloth. Never immerse 

the device into the water because of the risk of 

electric shock.