Ardesto JEG-1000 - Инструкция по эксплуатации - Страница 2

Operating time

This machine is designed with button switches of O grading, I 
grading, II grading (O for stop, I for weak grading, II for strong 
grading).  For juicing, select strong grading, for operating time, 
after operating for 1min, stop for 1min, then use again. After the 
above operation is performed for three times, stop for 15 min, do 
not operate until the motor is cooled, in this way, service life of 
this machine will be prolonged, the machine will serve you more 
efficiently.

1.Before using, please confirm the button switch of the main machine 
   in stop state, in this way, in case assembly is not completed, 
   starting the main machine can be avoided, so unnecessary 
   damage for persons or property avoided.
2.Before juicing, first confirm juicing net and rotor clutched in position, 

   and no hard contact between juicing net cutter and transparent 
   cover. Put the transparent cover on, put the handle into the cover 
   slot, then turn on the machine.
3.For using, assemble according to the diagram of "name and 
   position of main components". Turn on power supply, press 
   switch to let the machine run no-load for 5 sec. Put prepared 
   vegetable or fruit into feed port of the juicer, press with the 
   pushing bar, evenly, hard and slowly, juice of the vegetable or 
   fruit can be found, original, fresh, good for health.
4. Note: when pressing food with the pushing bar, force shall be 
   even or indirect, pressing force shall not be more than 1 kg, no 
   too sudden force, otherwise, juicing effect will be reduced. 

Juicing

3

 Diagram of name and position of main components

1

1.
   in for juicing, no cutting apart needed, easy and quick.
2.Design is fine, simple, and beautiful, with combined structure, 
   easy to operate and clean.
3.High speed electric motor with overheating protection is adopted, 
   high efficiency, time saving, energy saving, high service life of 
   the motor.
4.Safety lock unit for switching is specially designed, in order to 
   make sure safety and reliability in use.

For the juicer with large diameter, entire apple or pear can be put 

 Performances

Attention before using

1.This machine is set with safety unit, when the handle does not 
   fasten the cover or the cutter seat is not fastened, the motor cannot 
   turn, so as to ensure safety for the user.
2.When disassembling or assembling the juicer, press the upper 
   of feed port of the cover with your hand, then force the handle 
   to slide in or out of cover slot.
3.When disassembling juicing net, first remove the cover and residue 

   barrel, then turn the middle ring up to 30 degrees by holding juicing 
   nozzle with your hand, and take up, the juicing net will automatically 

   leave the rotor.

4.In order to avoid damage, before using, first check power supply 
   for compliance with rated voltage .
5.Clean all parts able to disassemble (refer to the section of 
   "maintenance and cleaning").
6.When assembling, please carefully read the diagram of "name 
   and position of main components".
7.Please carefully read the "attentions" before using.

2

1. Pushing bar  
2.Transparent cover  
3. Juicing net
4. Middle ring
5. Handle    

6. Residue barrel  
7. Rotor  
8. Main machine
9. Juicer jug

9

8

7

5

6

4

3

2

1

1.   Штовхач

2.  Прозора кришка

3.   Терка-фільтр

4.  З’єднувальна частина

5.   Ручка

6.  Контейнер для м’якоті

7.   Ротор

8.  Блок мотора

9.  Ємність для соку

ОПИС

Примітка:

 наведені в інструкції зображення призначені тільки для 

довідки. Реальний пристрій, імовірно, відрізняється.