Skil 6221 (F0156221LA) - Инструкция по эксплуатации - Страница 7

7

f) 

keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are less 

likely to bind and are easier to control.

g) 

Use the power tool, accessories and tool bits etc., in 

accordance with these instructions, taking into 

account the working conditions and the work to be 

performed.

 Use of the power tool for operations different 

from those intended could result in a hazardous situation.

5) SERVICE

a) 

Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

 This 

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR DRILL/DRIVERS

•  Avoid damage that can be caused by screws, nails and 

other elements in your workpiece; remove them before 

you start working

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the tool (tools with 

a rating of 230V or 240V can also be connected to a 

220V supply)

•  SKIL can assure flawless functioning of the tool only 

when original accessories are used

•  Use only accessories with an allowable speed matching 

at least the highest no-load speed of the tool

•  This tool should not be used by people under the age of 

16 years

•  Use completely unrolled and safe extension cords with a 

capacity of 16 Amps (U.K. 13 Amps)

•  Always keep the cord away from moving parts of the tool

•  If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug

•  Never use the tool when cord is damaged; have it 

replaced by a qualified person

•  If the drill bit becomes unexpectedly jammed (causing a 

sudden, dangerous reaction), immediately switch off the 

tool

•  In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the plug

• 

Secure the workpiece

 (a workpiece clamped with 

clamping devices or in a vice is held more securely than 

by hand)

• 

Hold the power tool only by the insulated gripping 

surfaces when performing an operation where the 

accessory may contact hidden wiring or its own 

power cord

 (contact with a “live” wire will also make 

exposed metal parts of the power tool “live” and shock 

the operator)

• 

Use suitable detectors to find hidden utility lines or 

call the local utility company for assistance

 (contact 

with electric lines can lead to fire or electrical shock; 

damaging a gas line can result in an explosion; 

penetrating a water pipe will cause property damage or 

an electrical shock)

• 

Do not work materials containing asbestos

 (asbestos 

is considered carcinogenic)

•  Dust from material such as paint containing lead, some 

wood species, minerals and metal may be harmful 

(contact with or inhalation of the dust may cause allergic 

reactions and/or respiratory diseases to the operator or 

bystanders); 

wear a dust mask and work with a dust 

extraction device when connectable

•  Certain kinds of dust are classified as carcinogenic (such 

as oak and beech dust) especially in conjunction with 

additives for wood conditioning; 

wear a dust mask and 

work with a dust extraction device when 

connectable

•  Follow the dust-related national requirements for the 

materials you want to work with

•  When you put away the tool, switch off the motor and 

ensure that all moving parts have come to a complete 

standstill

•  Always disconnect plug from power source before 

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

•  If for any reason the old plug is cut off the cord of this tool, 

it must be disposed of safely and not left unattended

USE

•  On/Off 

4

•  Speed control for smooth starting 

5

•  Changing direction of rotation 

6

-  when not properly set in left/right position, switch A 

2

cannot be activated

!  change direction of rotation only when tool is at a 

complete standstill

•  Changing bits 

7

-  insert the bit as deep as possible in the chuck

!  do not use bits with a damaged shank

•  Torque control (VariTorque) 

8

-  output torque will increase as clutch ring D is rotated 

from 1 to 20; position E will lock up the clutch to permit 

drilling or driving heavy duty work

-  when turning in a screw, first try VariTorque position 1 

and increase until the desired depth has been reached

•  Mechanical gear selection 

9

-  set selector F to desired speed

!  actuate the gear selector while tool is running 

slowly

LOW

-  low speed

-  high torque

-  for screwdriving and drilling large diameters

-  for tapping thread

HIGH

-  high speed

-  lower torque

-  for drilling small diameters

•  Holding and guiding the tool 

0

!  while working, always hold the tool at the 

grey-coloured grip area(s)

-  keep ventilation slots G 

2

 uncovered

-  do not apply too much pressure on the tool; let the tool 

do the work for you

APPLICATION ADVICE

•  Use the appropriate bits 

!

!  only use sharp bits

•  When drilling ferrous metals

-  pre-drill a smaller hole, when a large hole is required

-  lubricate drill bit occasionally with oil