SKIL 1612NA F0151612NA - Инструкция по эксплуатации - Страница 8

8

d) 

Store idle power tools out of the reach of children and 
do not allow persons unfamiliar with the power tool or 
these instructions to operate the power tool.

 Power 

tools are dangerous in the hands of untrained users.

e) 

Maintain power tools. Check for misalignment or 
binding of moving parts, breakage of parts and any 
other condition that may affect the power tool’s 
operation. If damaged, have the power tool repaired 
before use.

 Many accidents are caused by poorly 

maintained power tools.

f) 

keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are less 

likely to bind and are easier to control.

g) 

Use the power tool, accessories and tool bits etc., in 
accordance with these instructions, taking into 
account the working conditions and the work to be 
performed.

 Use of the power tool for operations diferent 

from those intended could result in a hazardous situation.

5) SERVICE

a) 

Have your power tool serviced by a qualified repair 
person using only identical replacement parts.

 This 

will ensure that the safety of the power tool is maintained.

SAFEtY INStRUCtIONS FOR MIXERS

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the tool (tools with 

a rating of 230V or 240V can also be connected to a 

220V supply)

•  Never use the tool without the protection frame

•  Never use the tool in or near an explosive atmosphere

•  Never mix combustible substances

•  Never reach with your hand or any other object into the 

mixing container during mixing

•  Wear protective gloves 

4

, a dust mask 

5

, close-itting 

clothes and sturdy shoes

•  The noise level when working can exceed 85 dB(A); 

wear ear protection

6

•  SKIL can assure lawless functioning of the tool only 

when the correct accessories are used which can be 

obtained from your SKIL dealer

•  Always disconnect plug from power source before 

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

•  If for any reason the old plug is cut of the cord of this tool, 

it must be disposed of safely and not left unattended

USE

•  On/of 

7

•  Switch locking for continuous use 

8

!  be aware of the forces that occur as a result of 

jamming; hold the tool firmly with both hands and 
take a secure stance

•  Speed control for smooth starting 

9

•  Maximum speed control 

0

With wheel C the maximum speed can be adjusted from 

low to high
-  switch on the tool
-  lock the switch

-  turn wheel C to select maximum speed

•  Mechanical gear selection 

!

 (

1612

)

-  set selector D to desired speed

!  actuate the gear selector only when tool is 

switched off

1 = LOW SPEED

-  high torque

-  for mixing high-density substances

2 = HIGH SPEED

-  lower torque

-  for mixing liquid substances

•  Protection frame 

@

-  for protecting the tool

-  for guiding the tool

-  for putting aside the tool in a simple way

-  mount protection frame E before using the tool for the 

irst time

!  never use the tool without the protection frame

•  Operating the tool

!  ensure that the tool is switched off

-  mount mixing paddle G onto spindle F as illustrated 

#

-  connect plug to power source

-  ensure the mixing container is securely positioned on 

the loor

-  dip the mixing paddle into the blending substance 

before switching on the tool

, and then gradually 

increase the blending speed by putting more pressure 

on trigger A 

2

 (so that the substance will not splash 

around and the tool will not be overloaded)

!  switch the tool off only when the mixing paddle is 

in the mixing container

•  Holding and guiding the tool 

$

!  while working, always hold the tool at the 

grey-coloured grip area(s)

!  always hold the tool firmly with both hands

MAINtENANCE / SERVICE

•  Always keep tool and cord clean (especially the 

ventilation slots)

-  always clean the mixer and functional parts after your 

mixing work

-  clean the tool with a dry, soft cloth (do not use cleaning 

agents or solvents)

-  clean ventilation slots H 

2

 regularly with a brush or 

compressed air

!  disconnect the plug before cleaning

•  If the tool should fail despite the care taken in manufacturing 

and testing procedures, repair should be carried out by an 

after-sales service centre for SKIL power tools

-  send the tool 

undismantled

 together with proof of 

purchase to your dealer or the nearest SKIL service 

station (addresses as well as the service diagram of 

the tool are listed on www.skilmasters.com)

ENVIRONMENt

• 

Do not dispose of electric tools, accessories and 
packaging together with household waste material

(only for EU countries)

-  in observance of European Directive 2012/19/EC on 

waste of electric and electronic equipment and its 

implementation in accordance with national law, 

electric tools that have reached the end of their life