Ryobi RCD18-220S (5133003736) - Инструкция по эксплуатации - Страница 3

English

1

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

EL

TR

UK

Safety, performance, and dependability have been given 
top priority in the design of your drill driver.

INTENDED USE

The drill driver is intended to be used only by adults who 
have read and understood the instructions and warnings 
in this manual, and can be considered responsible for their 
actions. The product can be used for drilling into various 
materials, including wood, metal, and plastics using a drill 
bit having a shank diameter of less than 13 mm.

The product can be used to drive and remove screws and 
bolts using an appropriate bit.

Do not use the product in any way other than those stated 
for intended use.

 WARNING

Read all safety warnings and all instructions.

 Failure 

to follow the warnings and instructions may result in 
electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

DRILL DRIVER SAFETY WARNINGS

■

Wear ear protectors when drilling.

 Exposure to noise 

can cause hearing loss.

■

Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

■

Hold power tool by insulated gripping surfaces, 
when performing an operation where the cutting 
accessory may contact hidden wiring

. Cutting 

accessory contacting a “live” wire may make exposed 
metal parts of the power tool “live” and could give the 
operator an electric shock.

■

Hold power tool by insulated gripping surfaces, 
when performing an operation where the fastener 
may contact hidden wiring.

 Fasteners contacting a 

“live” wire may make exposed metal parts of the power 
tool “live” and could give the operator an electric shock.

■

When not in use, all tools should be disconnected from 
power source.

■

The dust produced when using the product may pose 
a health hazard Do not inhale the dust. Wear a suitable 
dust mask.

■

Do not operate on materials (e.g., asbestos) that 
present a health hazard.

■

Switch off the product immediately if the bit stalls. Do 
not switch on the product again while the bit is stalled, 
as doing so could trigger a sudden recoil with a high 
reactive force. Determine why the bit stalled and rectify 
this, paying heed to the safety instructions.
The possible causes may be:

–

it is tilted in the workpiece

–

it has pierced the workpiece

–

the product is overloaded

■

Sawdust and splinters must not be removed while the 
product is running.

■

When working in walls, ceilings, or floors, avoid 
electrical cables and gas or water pipes.

■

Secure your workpiece with a clamping device.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The following hazards may arise, and the operator 
should pay special attention to avoid the following:

■

Risk of electrocution if electric cables are drilled into.  
Always grasp the product by designated handles; do 
not touch the drill bits.

■

Injury caused by vibration. Hold the product by 
designated handles and limit exposure to vibration. See 
“RISK REDUCTION”.

RISK REDUCTION

It has been reported that vibrations from hand-held tools 
may contribute to a condition called Raynaud’s Syndrome 
in certain individuals. Symptoms may include tingling, 
numbness and blanching of the 

fi

 ngers, usually apparent 

upon exposure to cold. Hereditary factors, exposure to 
cold and dampness, diet, smoking and work practices 
are all thought to contribute to the development of these 
symptoms. There are measures that can be taken by the 
operator to possibly reduce the effects of vibration:

■

Keep your body warm in cold weather. When operating 
the unit wear gloves to keep the hands and wrists 
warm. It is reported that cold weather is a major factor 
contributing to Raynaud’s Syndrome.

■

After each period of operation, exercise to increase 
blood circulation.

■

Take frequent work breaks. Limit the amount of 
exposure per day.

If you experience any of the symptoms of this condition, 
immediately discontinue use and see your doctor about 
these symptoms.

 WARNING

Injuries may be caused, or aggravated, by prolonged 
use of a tool. When using any tool for prolonged periods, 
ensure you take regular breaks.

MAINTENANCE

■

When servicing, use only identical Ryobi replacement 
parts. Use of any other parts may create a hazard or 
cause product damage.