Ryobi R14DDE-LL15S 5133001900 - Инструкция по эксплуатации - Страница 3

English

1

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

EL

TR

SPECIAL SAFETY RULES

■

Hold power tool by insulated gripping surfaces 
only, when performing an operation where the 
cutting accessory may contact hidden wiring. 

Cutting accessory contacting a “live” wire may make 
exposed metal parts of the power tool “live” and could 
give the operator an electric shock.

■

Hold power tool by insulated gripping surfaces 
when performing an operation where the fastener 
may contact hidden wiring. 

Fasteners contacting a 

“live” wire may make exposed metal parts of the power 
tool “live” and could give the operator an electric shock.

INTENDED USE

■

Drilling into

–

Wood

–

Metal

–

Plastic

–

Ceramic

■

Driving screws

MAINTENANCE

■

When servicing, use only identical replacement parts. 
Use of any other parts may create a hazard or cause 
product damage. 

■

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to damage from various types 
of commercial solvents and may be damaged by their 
use. Use clean cloths to remove dirt, dust, oil, grease, 
etc.

■

Always wear safety goggles or safety glasses with side 
shields during power product operation or when blowing 
dust. If operation is dusty, also wear a dust mask. 

■

To avoid serious personal injury, always remove 
the battery pack from the product when cleaning or 
performing any maintenance. 

■

Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils come in contact with 
plastic parts. Chemicals can damage, weaken or 
destroy plastic which may result in serious personal 
injury. 

■

Only the parts shown on the parts list are intended to 
be repaired or replaced by the customer. All other parts 
should be replaced at an authorized service center.

LED INDICATOR (FUEL GAUGE)

Battery charge

LED colour

66% - 100%

Green + Yellow + Red

33% - 66%

Yellow + Red

< 33%

 Red

NOTE:

 If only the red LED indicator is illuminated, it 

means the battery power is low. The battery needs to be 
recharged.

BATTERY OVERLOAD PROTECTION

This tool is designed to protect the battery from overloading. 
When overloading is detected, the tool will automatically 
switch off. To resume operation, switch the tool off and 
on again. If the tool fails to operate, it means battery pack 
is discharged and should be recharged in a compatible 
charger.

e-Torque control

e-Torque contol helps regulate the power output of the drill 
to avoid over-driving screws and damaging materials. To 
achieve a 

fl

 ush 

fi

 nish, it is best to select a low setting 

fi

 rst 

before commencing screw driving. When the e-Torque 
control engages, the fuel gauge LED indicator and worklight 
will 

fl

 ash and the drill will automatically shut down. 

If more power is required to drive the screw 

fl

 ush,  the 

e-Torque contol can be adjusted accordingly. e-Torque 
control only operates in screw driving mode, it has no effect 
on drilling mode.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 
of as waste. The machine, accessories 
and packaging should be sorted for 
environmental-friendly recycling.

SYMBOLS

Safety Alert

GOST-R conformity

CE Conformity

Please read the instructions carefully 
before starting the machine.

Waste electrical products should not be 
disposed of with household waste. Please 
recycle where facilities exist. Check with 
your local authority or retailer for recycling 
advice.