Ryobi R12SD-220S 5133005061 - Инструкция по эксплуатации - Страница 3

English

1

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL

Safety, performance, and dependability have been given 

top priority in the design of your drill driver.

INTENDED USE

The drill driver is intended to be used only by adults who 

have read and understood the instructions and warnings 

in this manual, and can be considered responsible for their 

actions.
The product can be used for drilling into various materials, 

including wood, metal, and plastics using a drill bit having 

a shank diameter of less than 10 mm. The product can 

be used to drive and remove screws and bolts using an 

appropriate bit.
Do not use the product in any way other than those stated 

for intended use.

 WARNING

Read all safety warnings, instructions, illustrations 
and specifications provided with this power tool.

Failure to follow all instructions listed below may result in 

HOHFWULFVKRFN¿UHDQGRUVHULRXVLQMXU\

Save all warnings and instructions for future reference.

DRILL DRIVER SAFETY WARNINGS

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

Ŷ

Hold the power tool by insulated gripping surfaces, 
when performing an operation where the cutting 
accessory or fasteners may contact hidden wiring. 

Cutting accessory or fasteners contacting a “live” wire 
may make exposed metal parts of the power tool “live” 
and could give the operator an electric shock.

SAFETY INSTRUCTIONS WHEN USING LONG DRILL 
BITS

Ŷ

Never operate at higher speed than the maximum 
speed rating of the drill bit.

 At higher speeds, the 

bit is likely to bend if allowed to rotate freely without 

FRQWDFWLQJWKHZRUNSLHFHUHVXOWLQJLQSHUVRQDOLQMXU\

Ŷ

Always start drilling at low speed and with the bit 
tip in contact with the workpiece.

 At higher speeds, 

the bit is likely to bend if allowed to rotate freely without 

FRQWDFWLQJWKHZRUNSLHFHUHVXOWLQJLQSHUVRQDOLQMXU\

Ŷ

Apply pressure only in direct line with the bit and do 
not apply excessive pressure.

 Bits can bend causing 

EUHDNDJHRUORVVRIFRQWUROUHVXOWLQJLQSHUVRQDOLQMXU\

ADDITIONAL SAFETY WARNINGS

Ŷ

Clamp workpiece with a clamping device.

8QFODPSHG ZRUNSLHFHV FDQ FDXVH VHYHUH LQMXU\ DQG

damage.

Ŷ

Ambient temperature range for tool during operation is 
between 0°C and 40°C.

Ŷ

Ambient temperature range for tool storage is between 
0°C and 40°C.

Ŷ

The recommended ambient temperature range for the 
charging system during charging is between 10°C and 
38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

 WARNING

7R UHGXFH WKH ULVN RI ¿UH SHUVRQDO LQMXU\ DQG SURGXFW

damage due to a short circuit, never immerse your 

WRRO EDWWHU\ SDFN RU FKDUJHU LQ ÀXLG RU DOORZ D ÀXLG WR

ÀRZ LQVLGH WKHP &RUURVLYH RU FRQGXFWLYH ÀXLGV VXFK

as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

Ŷ

Ambient temperature range for battery during use is 
between 0°C and 40°C.

Ŷ

Ambient temperature range for battery storage is 
between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.
Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or 
leaking. Check with the forwarding company for further 
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The following hazards may arise and the operator 
should pay special attention to avoid the following:

Ŷ

Damage to hearing caused by noise

–

Wear suitable hearing protection and limit exposure.

Ŷ

,QMXU\WRWKHH\HV

–

Wear protective eye shields or goggles when using 
the product.

Ŷ

,QMXU\FDXVHGE\YLEUDWLRQ

–

Limit exposure. Follow the instructions in Risk 
Reduction.

Ŷ

Electric shock caused by contact with hidden wires

–

Hold the product only by insulated surfaces.

Ŷ

,QMXU\FDXVHGE\GXVW

–

Dust created by operating the product can cause 

UHVSLUDWRU\ LQMXU\ :HDU DSSURSULDWH GXVW FRQWURO

mask with filters suitable for protecting against 
particles from the material being worked on.

RISK REDUCTION

It has been reported that vibrations from hand-held tools 

may contribute to a condition called Raynaud’s Syndrome 

in certain individuals. Symptoms may include tingling, 

QXPEQHVV DQG EODQFKLQJ RI WKH ¿QJHUV XVXDOO\ DSSDUHQW

upon exposure to cold. Hereditary factors, exposure to 

cold and dampness, diet, smoking and work practices 

are all thought to contribute to the development of these