Ryobi ONE+ R18PD7-252S 5133004391 - Инструкция по эксплуатации - Страница 3

1

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL

Safety, performance, and dependability have been given 
top priority in the design of your percussion drill.

INTENDED USE

The percussion drill is intended to be used only by adults 
who have read and understood the instructions and 
warnings in this manual, and can be considered responsible 
for their actions. 

The percussion drill is intended to be used in drilling into 
various materials, including wood, metal, and plastic using 
a drill bit having a shank diameter of less than 13 mm. When 
in impact mode, the percussion drill can be used in drilling 
masonry and similar materials. When in screwdriving 
mode, the percussion drill can be used in driving screws.

Do not use the product in any way other than those stated 
for intended use.

 WARNING

Read all safety warnings and all instructions.

 Failure 

to follow the warnings and instructions may result in 
electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

PERCUSSION DRILL SAFETY WARNINGS

■

Wear ear protectors when impact drilling. 

Exposure 

to noise can cause hearing loss.

■

Use auxiliary handle(s), if supplied with the tool. 

Loss of control can cause personal injury.

■

Hold power tool by insulated gripping surfaces 
when performing an operation where the cutting 
accessory may contact hidden wiring. 

Cutting 

accessory contacting a “live” wire may make exposed 
metal parts of the power tool “live” and could give the 
operator an electric shock.

■

Hold power tool by insulated gripping surfaces, 
when performing an operation where the fastener 
may contact hidden wiring.

 Fasteners contacting a 

“live” wire may make exposed metal parts of the power 
tool “live” and could give the operator an electric shock.

■

Do not operate on materials (e.g., asbestos) that 
present a health hazard.

■

Switch off the product immediately if the bit stalls. Do 
not switch on the product again while the bit is stalled, 
as doing so could trigger a sudden recoil with a high 
reactive force. Determine why the bit stalled and rectify 
this, paying heed to the safety instructions.
The possible causes may be:

–

it is tilted in the workpiece

–

it has pierced the workpiece

–

the product is overloaded

■

Sawdust and splinters must not be removed while the 
product is running.

■

When working in walls, ceilings, or floors, avoid 
electrical cables and gas or water pipes.

■

Secure your workpiece with a clamping device.

■

Ambient temperature range for tool during operation is 
between 0°C and 40°C.

■

Ambient temperature range for tool storage is between 
0°C and 40°C.

■

The recommended ambient temperature range for the 
charging system during charging is between 10°C and 
38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

 WARNING

To reduce the risk of 

fi

 re, personal injury, and product 

damage due to a short circuit, never immerse your 
tool, battery pack or charger in 

fl

 uid or allow a 

fl

 uid  to 

fl

 ow inside them. Corrosive or conductive 

fl

 uids,  such 

as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.

Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or 
leaking. Check with the forwarding company for further 
advice.

■

Ambient temperature range for battery during use is 
between 0°C and 40°C.

■

Ambient temperature range for battery storage is 
between 0°C and 20°C.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The operator should pay particular and additional 
attention to these points in order to reduce the risk of 
serious personal injury.

■

Injury to hearing – Wear suitable ear protection and limit 
exposure.

■

Injury to sight – Wear protective eye shields or goggles 
when using the product.

■

Injury caused by vibration – Limit exposure and follow 
the instructions on risk reduction in this manual.

■

Electric shock after contact with hidden wires – Hold the 
product only by insulated surfaces.

■

Respiratory injury from dust created by operating the 
product – Wear suitable protection depending on type 
of dust.