Ryobi ONE+ R18DD7-220S 5133004533 - Инструкция по эксплуатации - Страница 3

1

English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL

Safety, performance, and dependability have been given 
top priority in the design of your drill driver.

INTENDED USE

The drill driver is intended to be used only by adults who 
have read and understood the instructions and warnings 
in this manual, and can be considered responsible for their 
actions.

The drill driver can be used for drilling into various materials, 
including wood, metal, and plastics using a drill bit having 
a shank diameter of less than 13 mm. The product can 
be used to drive and remove screws and bolts using an 
appropriate bit.

Do not use the product in any way other than those stated 
for intended use.

 WARNING

Read all safety warnings, instructions, illustrations 
and specifications provided with this power tool.

Failure to follow all instructions listed below may result in 
electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

DRILL DRIVER SAFETY WARNINGS

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

■

Hold the power tool by insulated gripping surfaces, 
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.

Cutting accessory or fasteners contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.

SAFETY INSTRUCTIONS WHEN USING LONG DRILL 
BITS

■

Never operate at higher speed than the maximum
speed rating of the drill bit.

 At higher speeds, the

bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.

■

Always start drilling at low speed and with the bit
tip in contact with the workpiece.

 At higher speeds,

the bit is likely to bend if allowed to rotate freely without 
contacting the workpiece, resulting in personal injury.

■

Apply pressure only in direct line with the bit and do 
not apply excessive pressure.

 Bits can bend causing 

breakage or loss of control, resulting in personal injury.

ADDITIONAL SAFETY WARNINGS

■

Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify 
this, paying heed to the safety instructions.
The possible causes may be:

–

it is tilted in the workpiece

–

it has pierced the workpiece

–

the product is overloaded

■

Ambient temperature range for tool during operation is
between 0 

˚

C and 40

˚

 C.

■

Ambient temperature range for tool storage is between
0 

˚

C and 40

˚

 C.

■

The recommended ambient temperature range for the
charging system during charging is between 10 

˚

C and

38

˚

 C.

ADDITIONAL BATTERY SAFETY WARNINGS

 WARNING

To reduce the risk of 

fi

 re, personal injury, and product 

damage due to a short circuit, never immerse your 
tool, battery pack or charger in 

fl

 uid or allow a 

fl

 uid  to 

fl

 ow inside them. Corrosive or conductive 

fl

 uids,  such 

as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

■

Ambient temperature range for battery during use is
between 0 

˚

C and 40

˚

 C.

■

Ambient temperature range for battery storage is
between 0 

˚

C and 20

˚

 C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.

Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or 
leaking. Check with the forwarding company for further 
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The following hazards may arise, and the operator 
should pay special attention to avoid the following:

■

Damage to hearing caused by noise

–

Wear suitable hearing protection and limit exposure.

■

Injury to the eyes

–

Wear protective eye shields or goggles when using
the product.

■

Injury caused by vibration

–

Limit exposure. Follow the instructions in Risk
Reduction.

■

Electric shock caused by contact with hidden wires

–

Hold the product only by insulated surfaces.