Metabo SE 18 LTX 6000 620049890 - Инструкция по эксплуатации - Страница 10

ENGLISH

en

10

and comes into contact with your eyes, wash them 
with clean water and seek medical attention 
immediately!
LED lights (6): Do not observe the LED radiation 
directly with optical instruments.

See page 2.

1 Belt hook (mains powered tools) *
2 Rotation selector switch
3 Trigger  switch
4 Lock button (continuous operation)
5 Handle
6 LED  lights
7 Battery pack release button
8 Belt hook (cordless tools)*
9 Battery  pack  *

10 Capacity and signal indicator *
11 Capacity indicator button *
12 Depth stop
13 screwdriver bit*
14 Bit holder
15 Screwdriver spindle
16 Closure sleeve
17 Stop sleeve

* depending on the model / features

a

6.1

For mains powered machines only

Before plugging in, check that the rated mains 
voltage and mains frequency, as stated on the 

type plate match your power supply.

Always install an RCD with a maximum trip 
current of 30 mA upstream.

6.2

For cordless machines only

Battery pack

Charge the battery pack (9) before use.
If performance diminishes, recharge the battery 
pack.
The ideal storage temperature is between 10°C and 
30°C.
Li-Ion battery packs "Li-Power" have a capacity and 
signal indicator (10):
- Press the button (11), the LEDs indicate the 

charge level.

- If one LED is flashing, the battery pack is almost 

flat and must be recharged.

Removing and inserting the battery pack

Removal: Press the battery pack release button (7) 
and pull the battery pack (9) forwards.
To insert: Slide the battery pack (9) in until it 
engages.

Installation of belt hook

The belt hook (8) may be screwed into place on the 
left or the right (see illustration, page 2).

7.1

Setting the direction of rotation, 

engaging the transporting safety device 

(switch-on lock)

Do not activate rotation selector switch (2) 
unless the motor has completely stopped.

See page 2:

R

= Clockwise setting

L

= Counter-clockwise setting

0

= Central position: transportation lock setting 

(switch-on lock)

7.2

On/Off switch, modifying the speed

Switching on, speed:

 press the trigger switch (3).

Press in the trigger to increase the rotational 
speed.
To switch off release the trigger switch.

Continuous activation:

 With the trigger (3) 

pressed, push in the locking button (4) and 
release the trigger. Press and release the trigger 
again (3) to switch off.

In continuous operation, the machine 
continues running if it is forced out of your 

hands. Therefore, always hold the machine with 
both hands using the handles provided, stand 
securely and concentrate.

7.3

Screwdriver bit change

Inserting and removing the screwdriver bit:

- Remove the depth stop (12).
-

Insert:

 Insert the screwdriver bit (13) in the bit 

holder (14).

-

Remove:

 Pull the screwdriver bit (13) from the bit 

holder (14) using a pliers.

- Attach the depth stop (12) again:

turn and engage in position when mounted.

Note:
The bit holder (14) may be removed from the 
screwdriver spindle if the sleeve (16) is pulled back.

Never use 25 mm long 

screwdriver 

bits (13) in the screwdriver spindle 
(15)! Removal is not possible! Only 
use the bit holder (14)!

7.4

Working with depth stop

See page 2, illustration 2 a and 2 b.
To preset the screw insertion depth, one of the 
screws to be inserted is fitted on the screwdriver bit 
(13). Set the depth stop (12) by turning as follows:
a) Screws with heads designed to sit on top of the 
material (socket-head screws, oval head screws, 
hex screws):
the surface area of the screw head is 2 mm outside 
the stop sleeve (17).
b) Flat head screws:
the area of the screw head is 2 mm outside the stop 
sleeve (17).
Insert a screw as a test. Correct the screw depth if 
necessary:

5. Overview

6. Commissioning

7. Use