Metabo BE 1100 600582000 - Инструкция по эксплуатации - Страница 11

8. Cleaning, Maintenance

ENGLISH

en

11

Cleaning the keyless chuck:



After prolonged use hold the chuck vertically, with 

the opening facing down, and fully open and close it 

several times. The dust collected falls from the 

opening. Regular use of cleaning spray on the jaws 

and jaw openings is recommended.

9. Troubleshooting

Electronic signal display (6) (BE 1100, 

BE 1300 Quick)

Rapid flashing - restart protection



When power is restored after a power failure, the 

machine - which is still switched on - will not start by 

itself for safety reasons. Switch machine on and off 

again.
Slow flashing - carbon brushes worn



The carbon brushes are almost completely worn. 



If the brushes are completely worn, the machine 

switches off automatically. Have the brushes 

replaced by an authorised service centre.
Permanently lit - overload



If the machine is subject to continuous overloading 

for longer periods, the power input to the machine is 

limited. This prevents additional unauthorised 

heating of the motor.

10. Accessories

Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements 

and specifications listed in these operating instruc-

tions. 
Fit accessories securely. Secure the machine if it is 

operated in a bracket. Loss of control can cause 

personal injury.
For a complete range of accessories, see 

www.metabo.com or the main catalogue.

11. Repairs

Repairs to electrical tools must be carried out by 

qualified electricians ONLY! 
If you have Metabo electrical tools that require 

repairs, please contact your Metabo service centre. 

For addresses see www.metabo.com.
You can download spare parts lists from 

www.metabo.com.

12. Environmental Protection

Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

machines, packaging and accessories.

Only for EU countries: Never dispose of 

power tools in your household waste! In 

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment 

and its implementation in national legal systems, 

used power tools must be collected separately and 

handed in for environmentally compatible recycling.

13. Technical Specifications

Explanatory notes on the information on page 3.

Changes due to technological progress reserved.
P

1

= Rated  input

P

2

= Power output

n

1

*

= No-load speed

n

2

*

= Load  speed

ø max = Max. drill diameter

b

= Chuck capacity

G

= Drill spindle thread

H

= Drill spindle with hexagon socket

m

= Weight

D

= Collar diameter

Measured values determined in conformity with 

EN 60745.

Machine in protection class II

~

Alternating current

The technical specifications quoted are subject to 

tolerances (in compliance with the relevant valid 

standards).

* Energy-rich, high-frequency interference can cause 

fluctuations in speed. The fluctuations disappear, 

however, as soon as the interference fades away.

Emission values

Using these values, you can estimate the emis-

sions from this power tool and compare these with 

the values emitted by other power tools. The actual 

values may be higher or lower, depending on the 

particular application and the condition of the tool or 

power tool. In estimating the values, you should also 

include work breaks and periods of low use. Based 

on the estimated emission values, specify protective 

measures for the user - for example, any organisa-

tional steps that must be put in place. 
Vibration total value (vector sum of three directions) 

determined in accordance with EN 60745:

a

h, D

= Vibration emission value



(drilling into metal)

K

h,D

= Uncertainty (vibration)

Typical A-effective perceived sound levels:

L

pA

= Sound pressure level

L

WA

= Acoustic power level

K

pA

, K

WA

= Uncertainty

Wear ear protectors!