Makita DFS451RFE - Инструкция по эксплуатации - Страница 6

6

suitable for the screw, continue adjusting until you obtain 
the proper depth setting.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the 

battery cartridge is removed before carrying out any 
work on the tool.

Installing or removing the bit (Fig. 8)

To remove the bit, pull the locator. Then grasp the bit with 
a pair of pliers and pull the bit out of the magnetic bit 
holder. Sometimes, it helps to wiggle the bit with the pliers 
as you pull. 

(Fig. 9)

To install the bit, push it firmly into the magnetic bit holder. 
Then install the locator by pushing it firmly back.

Hook (Fig. 10)

The hook is convenient for temporarily hanging the tool. 
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool 
housing on either side and then secure it with a screw. To 
remove, loosen the screw and then take it out.

OPERATION

Screwdriving operation (Fig. 11)

Fit the screw on the point of the bit and place the point of 
the screw on the surface of the workpiece to be fastened. 
Apply pressure to the tool and start it. Withdraw the tool 
as soon as the clutch cuts in. Then release the switch 
trigger.

CAUTION:

• When fitting the screw onto the point of the bit, be 

careful not to push in on the screw. If the screw is 
pushed in, the clutch will engage and the screw will 
rotate suddenly. This could damage a workpiece or 
cause an injury.

• Make sure that the bit is inserted straight in the screw 

head, or the screw and/or bit may be damaged.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the 

battery cartridge is removed before attempting to 
perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the 

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs, 
carbon brush inspection and replacement, any other 
maintenance or adjustment should be performed by 
Makita Authorized Service Centers, always using Makita 
replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended 

for use with your Makita tool specified in this manual. 
The use of any other accessories or attachments might 

present a risk of injury to persons. Only use accessory 
or attachment for its stated purpose.

If you need any assistance for more details regarding 
these accessories, ask your local Makita Service Center.
• Phillips Insert bits
• Magnetic bit holder
• Various type of Makita genuine batteries and chargers
• Plastic carrying case

NOTE:

• Some items in the list may be included in the tool 

package as standard accessories. They may differ 
from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according 
to EN60745:

Model DFS441

Sound pressure level (L

pA

): 70 dB (A) or less

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model DFS451

Sound pressure level (L

pA

): 71 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined 
according to EN60745:

Work mode: screwdriving without impact
Vibration emission (a

h

): 2.5 m/s

2

 or less

Uncertainty (K): 1.5 m/s

2

ENG901-1

• The declared vibration emission value has been 

measured in accordance with the standard test method 
and may be used for comparing one tool with another.

• The declared vibration emission value may also be 

used in a preliminary assessment of exposure.

 WARNING:

• The vibration emission during actual use of the power 

tool can differ from the declared emission value 
depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the 

operator that are based on an estimation of exposure in 
the actual conditions of use (taking account of all parts 
of the operating cycle such as the times when the tool 
is switched off and when it is running idle in addition to 
the trigger time).

For European countries only

ENH101-15

EC Declaration of Conformity
We Makita Corporation as the responsible 
manufacturer declare that the following Makita 
machine(s):

Designation of Machine: 
Cordless Screwdriver
Model No./ Type: DFS441, DFS451
are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following 
standards or standardised documents:

EN60745