FERM FX Power CDM1165 - Инструкция по эксплуатации - Страница 5

5

EN

b)  

Use power tools only with speci

fi

 cally 

designated battery packs. 

Use of any other 

battery packs may create a risk of injury and 

fi

 re.

c)  

When battery pack is not in use, keep it 
away from other metal objects, like paper 
clips, coins, keys, nails, screws or other 
small metal objects that can make a 
connection from one terminal to another

. 

Shorting the battery terminals together may 
cause burns or a 

fi

 re.

d)  

Under abusive conditions, liquid may be 
ejected from the battery; avoid contact. 
If contact accidentally occurs, 

fl

 ush with 

water. If liquid contacts eyes, additionally 
seek medical help

. 

Liquid ejected from the 

battery may cause irritation or burns.

e)  

Do not use a battery pack or tool that is 
damaged or modi

fi

 ed.

Damaged or modi

fi

 ed 

batteries may exhibit unpredictable behaviour 
resulting in 

fi

 re, explosion or risk of injury.

f)  

Do not expose a battery pack or tool to 

fi

 re or excessive temperature.

Exposure to 

fi

 re or temperature above 130 °C may cause 

explosion. NOTE The temperature „130 °C“ 
can be replaced by the temperature „265 °F“.

g)  

Follow all charging instructions and do not 
charge the battery pack or tool outside 
the temperature range speci

fi

 ed in the 

instructions.

Charging improperly or at 

temperatures outside the speci

fi

 ed range may 

damage the battery and increase the risk of 

fi

 re.

6)  

Service

a)  

Have your power tool serviced by a 
quali

fi

 ed repair person using only identical 

replacement parts. 

This will ensure that the 

safety of the power tool is maintained.

b)  

Never service damaged battery packs.

Service of battery packs should only be 
performed by the manufacturer or authorized 
service providers.

Additional safety warnings for drills 
and screw drivers

a)  

Hold the power tool by insulated gripping 
surfaces, when performing an operation 
where the cutting accessory or fasteners 
may contact hidden wiring.

Cutting

accessory contacting a “live” wire may make

exposed metal parts of the power tool “live”

and could give the operator an electric shock.

”

Safety instructions when using long 
drill bits

a)  

Never operate at higher speed than the 
maximum speed rating of the drill bit. 

At higher speeds, the bit is likely to bend if

allowed to rotate freely without contacting the

workpiece, resulting in personal injury.

b)  

Always start drilling at low speed and with 
the bit tip in contact with the workpiece.

At higher speeds, the bit is likely to bend if

allowed to rotate freely without contacting the

workpiece, resulting in personal injury.

c)  

Apply pressure only in direct line with the bit 
and do not apply excessive pressure.

Bits

can bend causing breakage or loss of control,

resulting in personal injury.

Residual risks

Even when the power tool is used as 
prescribed it is not possible to eliminate all 
residual risk factors. The following hazards 
may arise in connection with the power tool’s 
construction and design:

a)  

Health defects resulting from vibration 
emission if the power tool is being used 
over longer period of time or not adequately 
managed and properly maintained.

b)  

Injuries and damage to property to due to 
broken accessories that are suddenly dashed.

Warning! 

This power tool produces an 

electromagnetic field during operation. 
This field may under some 
circumstances interfere with active or 
passive medical implants. To reduce the 
risk of serious or fatal injury, we 
recommend persons with medical 
implants to consult their physician and 
the medical implant manufacturer before 
operating this power tool.

2. MACHINE INFORMATION

Intended use

The impact driver is intended for driving in and 
loosening screws and bolts.

 
Not suitable for construction site usage.