Fein Scu7-9 72109400239 - Инструкция по эксплуатации - Страница 16

16

en

For your safety.

Read all safety warnings and all 
instructions.

 Failure to follow the 

warnings and instructions may result in electric shock, 
fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-
oughly read and completely understood this 
Instruction Manual and the enclosed “General 

Safety Instructions” (document number 
3 41 30 054 06 1). The documents mentioned should be 
kept for later use and enclosed with the power tool, 
should it be passed on or sold.
Please also observe the relevant national industrial safety 
regulations.

Intended use of the power tool:

Hand-held screwdriver for screwing in and unscrewing 
screws and nuts in weather-protected environments 
without water supply using the application tools and 
accessories recommended by FEIN.

Special safety instructions.

Hold power tool by insulated gripping surfaces, when 
performing an operation where the fastener may contact 
hidden wiring or its own cord. 

Fasteners contacting a 

“live” wire may make exposed metal parts of the power 
tool “live”" and could give the operator an electric shock.

Beware of any concealed electric cables, gas or water 
conduits; 

check the working area with a metal detector, 

for example, before commencing work.

Secure the workpiece firmly. 

A work piece that is gripped 

tightly in a clamping device or vice, is more secure than if 
held by hand.

Hold the power tool firmly. 

High reaction torque can 

briefly occur.

Do not machine any material containing asbestos. 

Asbes-

tos is cancerogenic.

Do not rivet or screw any name-plates or signs onto the 
power tool. 

If the insulation is damaged, protection 

against an electric shock will be ineffective. Adhesive 
labels are recommended.

Do not use accessories which are not specifically 
designed and recommended by the power tool manufac-
turer. 

Safe operation is not ensured merely because an 

accessory fits your power tool.

Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. 

The blower of the 

motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.

Before putting into operation, check the mains connec-
tion and the mains plug for damage.

Recommendation: The tool should always be supplied 
with power via a residual current device (RCD) with a 
rated current of 30 mA or less.

Hand/arm vibrations

The vibration emission level given in this information 
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare 
one tool with another. It may be used for a preliminary 
assessment of exposure.
The declared vibration emission level represents the 
main applications of the tool. However if the tool is used 
for different applications, with different accessories or 
poorly maintained, the vibration emission may differ. 
This may significantly increase the exposure level over 
the total working period.
An estimation of the level of exposure to vibration 
should also take into account the times when the tool is 
switched off or when it is running but not actually doing 
the job. This may significantly reduce the exposure level 
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool 
and the accessories, keep the hands warm, organisation 
of work patterns.

Operating instructions.

Adjust the Rotation selector switch only when the 
machine is at a complete stop.
For reliable working results, always carry out screwdriv-
ing operations using the depth stop.
SCU7-9: Use the auxiliary handle when working with the 
torque level “Fix” (rigid through-drive), as torques in 
excess of 28 Nm can develop. Do not use the depth stop.

Setting the torque (see page 6 – 7)

The factory setting is for the small to mid-size screw 
range.
The tightening torque also depends on the force with 
which the power tool is pressed against the screw.

Repair and customer service.

When working metal under extreme operat-
ing conditions, it is possible for conductive 
dust to settle in the interior of the power tool. 

The total insulation of the power tool can be impaired. 
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air, 
and connect a residual current device (RCD) on the line 
side.

m/s

2

m/s

2

Vibrational emission value according to EN 60745 
(vector sum of three directions)

h

m/s

2

m/s

2

Vibrational emission value (screwdriving)

m, s, kg, A, mm, V, 
W, Hz, N, °C, dB, 
min, m/s

2

m, s, kg, A, mm, V, 
W, Hz, N, °C, dB, 
min, m/s

2

Basic and derived units of measure from the inter-
national system of units 

SI

.

Character

Unit of measure, 
international

Unit of measure, 
national

Explanation

WARNING

OBJ_BUCH-0000000030-001.book  Page 16  Tuesday, April 19, 2011  1:13 PM