Fein SCT 5-40 X 72131300230 - Инструкция по эксплуатации - Страница 13

13

en

For your safety.

Read all safety warnings and all 
instructions.

 Failure to follow the 

warnings and instructions may result in electric shock, 
fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have 
thoroughly read and completely understood this 
Instruction Manual and the enclosed “General 

Safety Instructions” (document number 
3 41 30 465 06 0). The documents mentioned should 
be kept for later use and enclosed with the power tool, 
should it be passed on or sold.
Please also observe the relevant national industrial 
safety regulations.

Intended use of the power tool:

hand-guided screwdriver for screwing in and unscrew-
ing screws, especially for drywall screws, in weather-
protected environments using the application tools and 
accessories recommended by FEIN.
This power tool is also suitable for use with AC gener-
ators with sufficient power output that correspond to 
the Standard ISO 8528, design type G2. This Standard 
is particularly not complied with when the so-called dis-
tortion factor exceeds 10 %. When in doubt, please 
refer to the generator instruction/specification guide.
Observe the operating instructions and the national 
regulations for the installation and operation of the AC 
generator.

Special safety instructions.

Hold power tool by insulated gripping surfaces, when 
performing an operation where the fastener may con-
tact hidden wiring or its own cord. 

Fasteners contacting 

a “live” wire may make exposed metal parts of the 
power tool “live”" and could give the operator an elec-
tric shock.

Beware of any concealed electric cables, gas or water 
conduits. 

Check the working area before commencing 

work, e. g. with a metal detector.

Secure the work piece firmly. 

A work piece that is 

gripped tightly in a clamping device or vice, is more 
secure than if held by hand.

Hold the power tool firmly. 

High reaction torque can 

briefly occur.

Do not work materials containing magnesium. 

Danger 

of fire.

Do not work CFP (carbon-fiber-reinforced polymer) and 
materials containing asbestos. 

These materials are con-

sidered carcinogenic.

Do not rivet or screw any name-plates or signs onto the 
power tool. 

If the insulation is damaged, protection 

against an electric shock will be ineffective. Adhesive 
labels are recommended.

Do not use accessories which are not specifically 
designed and recommended by the power tool manu-
facturer. 

Safe operation is not ensured merely because 

an accessory fits your power tool.

Clean the ventilation openings on the power tool at reg-
ular intervals using non-metal tools. 

The blower of the 

motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.

Before putting into operation, check the mains connec-
tion and the mains plug for damage.

Recommendation: The tool should always be supplied 
with power via a residual current device (RCD) with a 
rated current of 30 mA or less.

Hand/arm vibrations

The vibration emission level given in this information 
sheet has been measured in accordance with a stand-
ardised test given in EN 62841 and may be used to 
compare one tool with another. It may be used for a 
preliminary assessment of exposure.
The declared vibration emission level represents the 
main applications of the tool. However, if the tool is 
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may 
differ. This may significantly increase the exposure level 
over the total working period.
An estimation of the level of exposure to vibration 
should also take into account the times when the tool 
is switched off or when it is running but not actually 
doing the job. This may significantly reduce the expo-
sure level over the total working period.

kg

kg

Weight according to EPTA-Procedure 01

L

pA

dB

dB

Sound pressure level

L

wA

dB

dB

Sound power level

L

pCpeak

dB

dB

Peak sound pressure level

K...

Uncertainty

m/s

2

m/s

2

Vibrational emission value according to EN 62841 
(vector sum of three directions)

h

m/s

2

m/s

2

Vibrational emission value (screwdriving)

m, s, kg, A, mm, V, 
W, Hz, N, °C, dB, 
min, m/s

2

m, s, kg, A, mm, V, 
W, Hz, N, °C, dB, 
min, m/s

2

Basic and derived units of measurement from the 
international system of units 

SI

.

Character

Unit of measure-
ment, international

Unit of measure-
ment, national

Explanation

WARNING

OBJ_BUCH-0000000389-001.book  Page 13  Monday, August 19, 2019  3:49 PM