Fein Ddsk672 72020600229 - Инструкция по эксплуатации - Страница 16

16

en

The declared vibration emission level represents the 

main applications of the tool. However if the tool is used 

for different applications, with different accessories or 

poorly maintained, the vibration emission may differ. 

This may significantly increase the exposure level over 

the total working period.

An estimation of the level of exposure to vibration 

should also take into account the times when the tool is 

switched off or when it is running but not actually doing 

the job. This may significantly reduce the exposure level 

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool 

and the accessories, keep the hands warm, organisation 

of work patterns.

Handling hazardous dusts

For work procedures with this power tool where mate-

rial is removed, dusts develop that can be hazardous to 

one’s health.

Contact with or inhaling some dust types, e. g. asbestos 

and asbestos-containing materials, lead-containing coat-

ings, metal, some wood types, minerals, silicate particles 

from materials containing stone, paint solvents, wood 

preservatives, and antifouling paints for vessels, can trig-

ger allergic reactions to the operator or bystanders and/

or lead to respiratory infections, cancer, birth defects or 

other reproductive harm. The risk from inhaling dusts 

depends on the exposition. Use dust extraction matched 

appropriately for the developing dust, as well as personal 

protective equipment and provide for good ventilation of 

the workplace. Leave the processing of asbestos-contain-

ing materials to specialists.

Wood and light-metal dust, hot mixtures of sanding dust 

and chemical materials can self-ignite under unfavourable 

conditions or cause an explosion. Avoid sparking in the 

direction of the dust collector as well as overheating of 

the power tool and the materials being sanded, empty 

the dust collector/container in time, observe the material 

manufacturer’s working instructions, as well as the rele-

vant regulations in your country for the materials being 

worked.

Operating instructions.

Before assembling, degrease the drive spindle and the 

internal taper of the drill chuck.
Change the gear setting or the rotation direction only 

after the motor has come to a complete stop.
For stationary use in a drill stand, remove the switched 

off power tool from the drill stand every 50 operating 

hours while at normal running temperature. Then, turn 

the machine around by 180° and run it for approx. 

1 minute to achieve uniform lubrication.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive 

dust to settle in the interior of the power 

tool. The total insulation of the power tool can be 

impaired. Blow out the interior of the power tool via the 

ventilation slots frequently with dry and oil-free com-

pressed air, and connect a residual current device (RCD) 

on the line side.

ASq672-1: For continuous use, apply grease via the 

corresponding lubrication nipple to the mechanical 

gearbox on a weekly basis.

If the supply cord of this power tool is damaged it must 

be replaced by a specially prepared cord available 

through the FEIN customer service centre.

If required, you can change the following parts yourself:

Drill chuck, application tools, Auxiliary handle

Warranty and liability.

The warranty for the product is valid in accordance with 

the legal regulations in the country where it is marketed. 

In addition, FEIN also provides a guarantee in accordance 

with the FEIN manufacturer’s warranty declaration.
The delivery scope of your power tool may include only 

a part of the accessories described or shown in this 

instruction manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product 

conforming with the relevant provisions given on the last 

page of this Instruction Manual.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should 

be sorted for environment-friendly recycling.

3 41 01 095 06 0.book  Seite 16  Montag, 15. März 2010  1:02 13