Fein ASCS 6.3 Select 71131163000 - Инструкция по эксплуатации - Страница 19

19

en

Before any work on the machine itself, remove the bat-
tery from the power tool. 

If the power tool accidentally 

starts, there is danger of injury.

Remove the battery only when the power tool is 
switched off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture 
and water. 

Clean contaminated battery terminals and 

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended 
for your power tool. 

When working with and charging 

incorrect, damaged, repaired or reconditioned batter-
ies, imitations or other brands, there is danger of fire 
and/or explosion.

Follow the safety warnings in the operating instructions 
of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information 
sheet has been measured in accordance with a stand-
ardised test given in EN 62841 and may be used to 
compare one tool with another. It may be used for a 
preliminary assessment of exposure.
The declared vibration emission level represents the 
main applications of the tool. However, if the tool is 
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may 
differ. This may significantly increase the exposure level 
over the total working period.
An estimation of the level of exposure to vibration 
should also take into account the times when the tool 
is switched off or when it is running but not actually 
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the oper-
ator from the effects of vibration such as: maintain the 
tool and the accessories, keep the hands warm, organi-
sation of work patterns.

Operating Instructions.

Adjust the rotation selector switch only when the 
machine is at a complete stop.
To avoid accidental starting, e. g., during transport, set 
the rotation selector switch to the centre position.
When overheated, the machine runs with short, low-
power impulses. Allow the machine to cool down at 
no-load speed.
For reliable working results, always carry out screw-
driving operations using the depth stop.

Electronic torque shut-off (see pages 6 – 7).

The electronic torque shut-off can be used when work-
ing without depth stop.
Adjust the torque only when the machine is at a com-
plete stop.
The motor switches off when reaching the set torque 
and an audio signal sounds. After the shut-off has taken 
place, release the on/off switch and press it again for the 
next screwdriving operation.
The audio signal can be switched on and off.
The electronic shut-off is deactivated when working in 
the “

” torque level.

To achieve good working results, press the power tool 
with sufficient force against the screw.

Handling the battery.

Store, operate and charge the battery only using FEIN 
battery chargers within the battery operating-tempera-
ture range between 5 °C – 45 °C (41 °F – 113 °F). At 
the beginning of the charging procedure, the battery 
temperature must be within the battery operating-tem-
perature range.

The real percentage of the battery charge condition is 
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor 
prior to the battery being deep discharged.

Repair and customer service.

When working metal under extreme oper-
ating conditions, it is possible for conductive 
dust to settle in the interior of the power 

tool. Blow out the interior of the power tool via the 
ventilation slots frequently with dry and oil-free com-
pressed air. 
Products that have come into contact with asbestos 
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable 
country-specific regulations for such disposal.
The current spares parts list for this power tool can be 
found on our website at www.fein.com.

If required, you can change the following parts your-
self:

 application tools, depth stop, battery, belt clip

Warranty and liability.

The warranty for the product is valid in accordance 
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in 
accordance with the FEIN manufacturer’s warranty dec-
laration.
The delivery scope of your power tool may include 
only a part of the accessories described or shown in this 
Instruction Manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product 
conforming with the relevant provisions given on the 
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-D1_IA, 
D-73529 Schwäbisch Gmünd

LED indica-
tor

Meaning

Activity

1 – 4 green 
LED

Percentage of 
charge condi-
tion

Operation

Continu-
ous red 
light

Battery is 
almost empty

Charge battery

Red flash-
ing light

Battery is not 
ready for 
operation

Bring the battery into 
the battery operating-
temperature range, 
then charge

OBJ_BUCH-0000000372-001.book  Page 19  Thursday, February 14, 2019  10:52 AM