Fein ASB 18 Q Select 71132364000 - Инструкция по эксплуатации - Страница 22

22

en

depends on the exposition. Use dust extraction matched 
appropriately for the developing dust, as well as personal 
protective equipment and provide for good ventilation of 
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of grinding dust 
and chemical materials can self-ignite under unfavourable 
conditions or cause an explosion. Avoid sparking in the 
direction of the dust collector as well as overheating of 
the power tool and the materials being sanded, empty the 
dust collector/container in time, observe the material 
manufacturer’s working instructions, as well as the rele-
vant regulations in your country for the materials being 
worked.

Operating Instructions.

Adjust the rotational direction switch and the gear switch 
only when the machine is at a complete stop.
Always push the gear switch through to the stop. Other-
wise, the machine can become damaged.
Thermal overload of the power tool is indicated through 
flashing of the LED in the handle.
In case of overload, the machine switches off.
To avoid accidental starting, e. g., during transport, set 
the rotation selector switch to the centre position.

Setting the torque 

The torque setting is for the small to mid-size screw 
range.

Handling the battery.

Operate and charge the battery only within the battery 
operating-temperature range of 0 °C – 45 °C (32 °F –
113 °F). At the beginning of the charging procedure, the 
battery temperature must be within the battery operat-
ing-temperature range.

The real percentage of the battery charge condition is 
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor prior 
to the battery being deep discharged.

ASB18 Q (**): Use of accessories with activated 
impact function

With activated impact function, only the drill chuck from 
our accessories program may be used. When using other 
QuickIN accessories, the power tool, the application 
tool, the accessory or the workpiece can become dam-
aged.

Repair and customer service.

When working metal under extreme operat-
ing conditions, it is possible for conductive 
dust to settle in the interior of the power tool. 

Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air. 
TThe current spares parts list for this power tool can be 
found on our website at www.fein.com.

If required, you can change the following parts yourself:

application tools, battery, belt hook, bit garage, drill 
chuck

Warranty and liability.

The warranty for the product is valid in accordance with 
the legal regulations in the country where it is marketed. 
In addition, FEIN also provides a guarantee in accordance 
with the FEIN manufacturer’s warranty declaration.
The delivery scope of your power tool may include only 
a part of the accessories described or shown in this 
Instruction Manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product 
conforming with the relevant provisions given on the last 
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-D1_IA, 
D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out power tools and accessories should 
be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insulate 
the terminals with tape as a protective measure against 
short-circuiting.

LED indicator

Meaning

Activity

1 – 4 green 
LED

Percentage of 
charge condi-
tion

Operation

Continuous 
red light

Battery is 
almost empty

Charge battery

Red flashing 
light

Battery is not 
ready for 
operation

Bring the battery into 
the battery operating-
temperature range, 
then charge

OBJ_BUCH-0000000300-001.book  Page 22  Tuesday, March 20, 2018  8:14 AM