Шуруповерты Einhell TE-MX 1600-2 CE Twin HEX 4258561 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
GB
- 17 -
Left: stirrer 1 / right: stirrer 2
•
The mixture is mixed from the bottom up.
For tacky and viscous materials such as:
- tile adhesives
- ready-mixed mortar
-
fi
lling compounds
-
screeds
6. Operation
6.1 ON/OFF switch (Fig. 5/Item 1)
First
fi
t a suitable mixing tool to the equipment
(see 5.)
Connect the mains plug to a suitable socket.
To switch on:
Press the ON/OFF switch (1)
Continuous operation:
Secure the ON/OFF switch (1) with the locking
button (3).
To switch o
ff
:
Press the ON/OFF switch (1) brie
fl
y.
6.2 Speed control (Fig. 6/Item 2)
To pre-select the speed turn the knurled screw (2)
on the switch.
Plus direction:
Higher speed
Minus direction:
Lower spee
Constant electronics
This tool is equipped with constant electronics.
With constant electronics, the set speed is kept
constant even when the tool is working under
load.
6.3 De
fi
ning the speed range (Fig. 7/Item 5)
The gear selector switch (5) enables you to work
within a speci
fi
c speed range.
Switch position, setting 1 (A)
Speed range: high torque, low speed
Switch position, setting 2 (B)
Speed range: low torque, high speed
Note!
Change the gear only when the drill is at a
standstill. If you fail to observe this point, the gea-
ring may be damaged.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a quali
fi
ed electrician.
Danger!
The carbon brushes should not be rep
laced by anyone but a quali
fi
ed electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
Anl_TE_MX_1600_2_CE_Twin_SPK9.indb 17
Anl_TE_MX_1600_2_CE_Twin_SPK9.indb 17
30.08.2017 16:10:11
30.08.2017 16:10:11
