Einhell TE-CI 12 Li - Инструкция по эксплуатации - Страница 20

GB

- 20 -

6. Operation

6.1 Charging the Li battery pack (Fig. 2-3)

1.  Remove the battery pack (5) from the handle, 

pressing the pushlock button (8) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(6) into the mains socket outlet. The green 

LED will then begin to 

fl

 ash.

3.  Push the battery pack onto the battery char-

ger. 

In section 10 (Charger indicator) you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to charge, check for the 

following:

• 

 voltage at the power socket

• 

 whether there is good contact at the charging 

contacts of the charging unit.

If the battery pack still fails to charge, send

• 

 the charger and charging adapter

• 

 and the battery pack

to our customer service center.

6.2 Changeover switch (Fig. 4/Item 3)

The slide switch above the On/O

ff

  switch is for 

setting the direction of rotation of the cordless 

screwdriver and for preventing the cordless 

screwdriver from being switched on inadvertently. 

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to 

the gearing, the direction of rotation must only be 

changed when the equipment is at a standstill. 

When the slide switch is in the middle position, 

the On/O

ff

  switch is blocked.

6.3 On/O

ff

  switch (Fig. 4 / Item 4)

In

fi

 nitely variable speed control is possible with 

the On/O

ff

  switch. The further you push the 

switch, the higher the speed of the cordless 

screwdriver.

To switch on:

Press the On/O

ff

  switch (4).

To switch o

ff

 :

Release the ON/OFF switch (4)

6.4 Battery capacity indicator (Fig. 5 – Item 2)

Press the battery capacity indicator switch (a). 

The battery capacity indicator (2) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

The yellow and red LEDs are lit:

The battery has an adequate remaining charge.

Red LED is lit:

The battery is empty, recharge the battery.

6.5 LED lamp (Fig. 4/Item 7)

The LED lamp (7) can be used in poor lighting 

conditions to illuminate the area where you want 

to screw. The LED light (7) will come on automati-

cally as soon as you press the On/O

ff

  switch (4). 

6.6 Changing the bit (Fig. 6)

Important! Set the changeover switch (3) to its 

center position whenever you carry out any work 

(for example changing the tool, maintenance 

work, etc.) on the cordless screwdriver.

Inserting the bit:

• 

 Insert the bit into the bit mount (1) as far as 

the stop while simultaneously pulling the slee-

ve on the bit mount (1) toward the bit.

• 

 Release the sleeve again.

• 

 Check that the bit is securely seated.

Removing the bit:

• 

 Pull the sleeve on the bit mount (1) toward the 

bit, hold it tight and remove the bit.

6.7 Screws

It is advisable to use self-centering screws (e.g. 

Torx, cross recessed head) as these will enable 

you to work safely and reliably. Always make sure 

that the bit used is of the same size and shape as 

the screw.

Anl_TE_CI_12_Li_SPK9.indb   20

Anl_TE_CI_12_Li_SPK9.indb   20

06.03.2018   11:13:38

06.03.2018   11:13:38