Einhell PXC TE-CI 18 Li Brushless-Solo 4510030 - Инструкция по эксплуатации - Страница 19

GB

- 19 -

If the battery pack still fails to charge, send

• 

 the charger and charging adapter

• 

 and the battery pack

to our customer service center.

6.2 Changeover switch (Fig. 4/Item 3)

The slide switch above the On/O

ff

  switch is for 

setting the direction of rotation of the cordless 

screwdriver and for preventing the cordless 

screwdriver from being switched on inadvertently. 

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to 

the gearing, the direction of rotation must only be 

changed when the equipment is at a standstill. 

When the slide switch is in the middle position, 

the On/O

ff

  switch is blocked.

6.3 On/O

ff

  switch (Fig. 4 / Item 4)

In

fi

 nitely variable speed control is possible with 

the On/O

ff

  switch. The further you push the 

switch, the higher the speed of the cordless 

screwdriver.

To switch on:

Press the On/O

ff

  switch (4).

To switch o

ff

 :

Release the ON/OFF switch (4)

6.4 Battery capacity indicator (Fig. 5 – Item 2)

Press the battery capacity indicator switch (a). 

The battery capacity indicator (2) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

6.5 LED lamp (Fig. 6/Item 7)

The LED lamp (7) can be used in poor lighting 

conditions to illuminate the area where you want 

to screw. The LED light (7) will come on automati-

cally as soon as you press the On/O

ff

  switch (4). 

6.6 Changing the bit (Fig. 7)

Important! Set the changeover switch (3) to its 

center position whenever you carry out any work 

(for example changing the tool, maintenance 

work, etc.) on the cordless screwdriver.

Inserting the bit:

• 

 Insert the bit into the bit mount (1) as far as 

the stop while simultaneously pulling the slee-

ve on the bit mount (1) toward the bit.

• 

 Release the sleeve again.

• 

 Check that the bit is securely seated.

Removing the bit:

• 

 Pull the sleeve on the bit mount (1) toward the 

bit, hold it tight and remove the bit.

6.7 Screws

It is advisable to use self-centering screws (e.g. 

Torx, cross recessed head) as these will enable 

you to work safely and reliably. Always make sure 

that the bit used is of the same size and shape as 

the screw.

7.  Cleaning, maintenance and 

ordering of spare parts

Danger!

Always remove the battery pack before making 

adjustments to the equipment.

7.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

7.2 Maintenance

There are no parts inside the equipment which  

require additional maintenance.

Anl_TE_CI_18_Li_Brushless_SPK7.indb   19

Anl_TE_CI_18_Li_Brushless_SPK7.indb   19

03.05.16   15:20

03.05.16   15:20