Bosch GSR 180-LI с 1 батареей 2.0 A*ч 06019F8125 - Инструкция по эксплуатации - Страница 9

 English | 

9

Bosch Power Tools

1 609 92A 34M | (15.9.16)

The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This 
may significantly increase the exposure level over the total 
working period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working 
period.

Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns.

Assembly

Battery Charging

Note: 

The battery supplied is partially charged. To ensure full 

capacity of the battery, completely charge the battery in the 
battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure 
does not damage the battery.

The lithium-ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.



Do not continue to press the On/Off switch after the 
machine has been automatically switched off. 

The bat-

tery can be damaged.

Removing the battery

The battery 

7

 is equipped with two locking levels that should 

prevent the battery from falling out when pushing the battery 
unlocking button 

8

 unintentionally. As long as the battery is 

inserted in the power tool, it is held in position by means of a 
spring.

To remove the battery 

7

, press the unlocking button 

8

 and 

pull out the battery toward the front. 

Do not exert any force.

Changing the Tool (see figure A)



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.

Open the keyless chuck 

2

 by turning in rotation direction 



, 

until the tool can be inserted. Insert the tool.

Firmly tighten the collar of the keyless chuck 

2

 by hand in ro-

tation direction 



. This automatically locks the drill chuck.

Dust/Chip Extraction



Dust from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health and cause allergic reactions, lead to res-
piratory infections and/or cancer.

 Materials containing 

asbestos may only be worked by specialists.

–

Provide for good ventilation of the working place.

–

It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dust can 

easily ignite.

GSR  140-LI

GSR  180-LI

GSB  140-LI

GSB  180-LI

Vibration total values a

h

 (triax vector sum) 

and uncertainty K determined according to 
EN 60745-2-1, EN 60745-2-2.

Drilling in metal:
a

h

K

Impact drilling in concrete:
a

h

K

Screwdriving:
a

h

K

m/s

2

m/s

2

m/s

2

m/s

2

m/s

2

m/s

2

<2.5

1.5

–
–

<2.5

1.5

2.5
1.5

–
–

<2.5

1.5

<2.5

1.5

7.0
1.5

<2.5

1.5

2.5
1.5

8.0
1.5

<2.5

1.5

OBJ_BUCH-3028-001.book  Page 9  Thursday, September 15, 2016  10:18 AM